Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
setup unpacking your new mini rotary tool was carefully packaged for safe shipping. if you discover any damage after you have signed for delivery, immediately call Customer Service at (570) 546-9663 for advice. save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of the shipment, you should inventory the contents. inventory model t10165 inventory (figure 1) a. Collet 3.32" (pre-installed)..................... 1 b. Mini rotary tool................................. 1 c. abrasive Cones: —Coarse grit (yellow) ....................... 5 —Medium grit (Blue) ......................... 5 d. threaded Mandrels (for cones).......... 2 e. Collet 1.8"............................................. 1 f. steel Bits: —round head 1.4mm ....................... 1 —Cylindrical 2.1mm........................... 1 g. diamond Bits: —round head 2mm .......................... 1 —Flame 3mm .................................... 1 —Cylindrical 1.2mm........................... 1 —spear 2mm..................................... 1 B C gEd a F figure 1. Model t10165 inventory. Model t10165 high-precision Mini rotary tool -5 operations operating this tool can propel objects into the air that may cause eye damage. to protect yourself from this hazard, alWays wear ansi approved safety glasses or goggles during operation. mandrels & bits your mini rotary tool is supplied with two threaded mandrels that hold that hold the abrasive cones. to install an abrasive cone onto a mandrel, screw the threaded tip of the mandrel into the bottom of the cone. note: The cones with yellow bottoms are coarse abrasives, and the ones with blue bottoms are a medium abrasive. to install a mandrel or bit: 1. disCoNNECt tool FroM poWEr! 2. press and hold the spindle lock to keep the spindle from rotating, then loosen the collet nut (see figure 2). figure 2. Model t10165 controls. Collet Nut spindle lock rotary speed dial 3. Fully insert the mandrel or bit shank into the collet until it stops, then retighten the collet nut. note: Only tighten the collet nut until the mandrel or bit cannot be removed when you tug on it. Overtightening may damage the components. operation rules follow these rules to ensure a safe and efficient operation: • turn the rotary speed dial to OFF before connecting the tool to power. • to prevent injuries from tool slippage, alWays secure the workpiece in a vise or other clamping device. NEVEr hold the workpiece by hand during operation. • For efficient control of the tool, start your operation with the slowest speed, then increase the speed as needed. • to avoid the tool slipping in your hand, make sure your hands are clean and dry. • to prevent excessive wear of the motor components, NEVEr operate this tool for longer than five continuous minutes. turn it OFF after this time and allow it to cool for five minutes. • to ensure a good finish, ease the cone or bit into the workpiece. Jamming it into the workpiece may damage the tool components or the workpiece. • When using the abrasive cones, use the tip of the cone. otherwise, the abrasive material may unravel. -6- Model t10165 high-precision Mini rotary tool accessories t20501—face shield crown protector 4" t20502—face shield crown protector 7" t20503—face shield Window t20452—"Kirova" anti-reflective safety glasses t20451—"Kirova" clear safety glasses h0736—shop fox® safety glasses h7194—bifocal safety glasses 1.5 h7195—bifocal safety glasses 2.0 h7196—bifocal safety glasses 2.5 h1432—multi-positional hobby vise this handy, go-anywhere vise features a powerful suction mechanism that securely attaches the vise to any smooth, flat surface. the swivel head can be positioned in just about any configuration and locks in place with a high torque lock ring. ideal for hobby use around the home or take it anywhere. steel jaws have protective rubber pads and measure 23.4" wide. open capacity is 21.2". figure 3. Eye protection assortment. h7194 h0736 t20503 t20451 t20502 t20452 figure 4. Model h1432 hobby vise. Model t10165 high-precision Mini rotary tool -7 replacement parts 1 Consists of: 5 Each Coarse Abrasive Cones 5 Each Medium Abrasive Cones 2 3 Consists of: 1 Each Round Head 1.4mm Steel Bit 1 Each Cylindrical 2.1mm Steel Bit 1 Each Round Head 2mm Diamond Bit 1 Each Flame 3mm Diamond Bit 1 Each Cylindrical 1.2mm Diamond Bit 1 Each Spear 2mm Diamond Bit Consists of: 1 Each Collet Nut 1 Each 3.32" Collet 1 Each 1.8" Collet 2 Each Threaded Mandrels REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT10165001 ABRASIVE KIT 2 PT10165002 BIT KIT 3 PT10165003 COLLET/MANDREL KIT -8-Model t10165 high-precision Mini rotary tool Warranty grizzly industrial, inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. this warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, acci...