120 Volt Electrical Installation Always follow applicable local, state and federal codes and guidelines. Use only a dedicated electrical line with a 20 amp breaker. Cord-and-plug connections may not use a cord longer than 15 feet (4.6 m) and must be plugged into a dedicated 20 amp GFCI connection (NEC 680.42(A)(2)). Do not use extension cords! Always use a weatherproof-covered receptacle. Receptacle shall be located not less than 5 feet (1.5 m) from and not exceeding 10 feet (3.0 m) from the ins

The panel will display “TEMP LOCK” when the set temperature is locked. To unlock the set temperature: Press the “UP” or “DOWN” button, “TIME”, “JETS 1”, and then the “DOWN” button. Circulation Pump This is an optional feature. The circulation pump will come on when the system is checking temperature, during filter cycles, during freeze conditions, or when another pump is on. Preset Filter Cycles There are two filter cycles per day. The start and end times of each cycle are programmable. To progr

(Displays on third occurrence of dr message.) Spa is shut down. Follow action required for dr message. Spa will not automatically reset; you may press any button to reset. Pr When your spa is first actuated, it will go into priming mode. The priming mode will last for up to four minutes and then the spa will begin to heat and maintain the water temperature in the Standard mode. --F or --C Temperature unknown After the pump has been running for two minutes, the temperature will be displayed. - -

All rights reserved. Duplication without written consent is strictly prohibited. Cal Spas® is a registered trademark. Due to continuous improvement programs, all models, operation, and/or specifications are subject to change without prior notice. LTR20081024, Rev. B 6/12/08 CONTACT INFORMATION For customer service, please contact your authorized dealer immediately. If you need additional information and/or assistance, please contact: L.M.S. Customer Service Department 1462 East Ninth Street Pomo

Make sure the spa is positioned so that access to the equipment compartment and all side panels will not be blocked. Be certain that your installation will meet all city and local safety codes and requirements. Consider how you will use your spa How you intend to use your spa will help you determine where you should position it. For example, will you use your spa for recreational or therapeutic purposes? If your spa is mainly used for family recreation, be sure to leave plenty of room around it

If the area receives direct sunlight, you will want to provide some • protection for the equipment portion of the equipment pack. The equipment pack and heater are delivered separately. Do not cover gas heaters unless properly vented. (See heater owner’s manual for important safety information.) Portable Spa Site Preparation Your spa needs a solid and level foundation. The area that it sits on must be able to support the weight of the spa, with water and the occupants who use it. If the foundati

If the slope is relatively minor, contact your local building safety. Site Excavation – Hard Bottom For hard bottom placement for in-ground spas, you will need a smooth and flat concrete surface at least 4” thick as large as the bottom contact points. Be sure not to seal the bottom off and making a sealed box. You will need adequate water drainage for escape under the spa. A gravel beds around the concrete base will help with this. Site Excavation – Sand Bottom With the spa area and all elevatio

Contents Pre-Delivery and Installation Checklist.................................................1 Portable Spa Site Preparation................................................................4 In-Ground Spa Site Preparation.............................................................4 Getting the Spa Into Your Yard...............................................................6 Electrical Requirements.........................................................................8 Electrical Requireme

Lay out the extension loom to verify that you have enough length to 4. reach the control box. Remember that conduit runs are not generally run in a straight line. Every bend, and up and down run consumes line length. Take this into consideration when verifying electrical and plumbing runs. Connect the extension loom to the control panel location on the circuit 5. board located inside the control box. You will also need to connect both the temperature and high limit sensors to the circuit board p

Wire runs over 85 feet must increase wire gauge to the next lower number. For example: A normal 50 amp RCD with four #8 AWG copper wires run over 85 feet would require you to go to four #6 AWG copper wires. Spa Model GFCI Required Wires Required Portable Spas All 230V spas (except 6205 control boxes requiring high amperage - see below) One 32 amp RCD or two 16 amp RCDs Four #10 AWG copper wires Spas with the 6300 control box (when high amperage is selected on circuit board) SEE CONFIGURATION INS