Votes - , Average rating:
(
)
)
Manafacture: Heath Zenith
File size: 271.59 kb
File name: 598-1235-01.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Contact a qualified electrician if there is any question as to the suitability of the system. Lamp in Fixture Contains Mercury. Dispose According to Local, State, or Federal Laws. WARNING: Turn power off at the fuse or circuit breaker. This fixture can be mounted on a wall with, or without using a flush-mounted junction box. Do not attempt to mount this fixture on a surface-mounted “Wet Location” junction box. Use the instructions below that apply to your application. Installation Using A Junction Box Note: If your junction box protrudes out of the wall slightly, you may want to use the enclosed gasket so less caulking is required. 1. Hold the Mounting Bracket and Gasket over the junction box. Thread the supply wires through the large hole in the back of the Mounting bracket. Select the holes in the mounting bracket that line up with the screw holes in the junction box. Make sure the bottom of the Mounting Bracket is level. Secure with the two #8 screws provided. Installation Without A Junction Box 1. Select a location on a flat wall with structurally sound wood and from 5 to 25 feet from the ground. The wood should be at least one inch thick to safely secure the fixture. 2. Use the Mounting Bracket as a template. Hold it at the desired mounting location (making sure the bottom is level), and mark four mounting holes. 3. Use four #8 or #10 wood screws or galvanized deck screws at least 1 inch long (not provided) to secure the Mounting Bracket to the wall. It may be necessary to drill appropriate pilot holes if mounted to hardwood to avoid splitting. 4. Remove the knockout in the bottom of the Mounting Bracket, and bring your supply wires through this knockout using appropriate flexible conduit or other approved means of wiring. Complete The Installation 1. Put the Temporary Pin through the holes in the Mounting Bracket. 2. This fixture must be grounded. Connect the supply ground wire to the green ground screw. You can also attach a bare or green “pigtail” to the green ground screw, then connect the ground pigtail to the supply ground when the other supply wires are connected. 3. Slide the fixture onto the Mounting Bracket, and allow the fixture to rest on the Temporary Pin. 4. Connect the fixture wires to the supply wires (black to black, white to white, and if a ground pigtail was added above, connect this pigtail to the supply ground wire). Secure with the wire connectors provided. 5. Remove the Temporary Pin, and slide the fixture all the way down onto the Mounting Bracket making sure no wires get pinched. 6. Install the screw through the bottom of the Mounting Bracket and into the fixture housing. Tighten this screw. 7. Install ONLY a 70 watt high pressure sodium type S62 lamp (provided). 8. Caulk fixture mounting surface with silicone weather sealant. To test operation during daylight, cover the photocontrol with black tape. Turn on the power. The light will take up to ten minutes to reach full brightness. Remove the tape from the photocontrol and your unit will operate automatically—on at dusk, off at dawn. Photocontrol Gasket (Optional) Mounting Bracket Ground Screw Fixture Lamp Temporary Pin © 2007 HeathCo LLC 598-1235-01 Ballast Assembly Replacement Instructions Ballast assembly can be replaced without the cutting of any wires. Use of a qualified electrician is recommended. WARNING: Turn power off at the fuse or circuit breaker. 1. Remove plastic cover. 2. Remove bulb. 3. Remove five screws attaching reflector to fixture housing. 4. Label wires according to wiring diagram. 5. Remove wire nuts from wires. Retain wire nuts to connect replacement ballast assembly. 6. Remove two screws and lock washers holding ignitor and ballast in place. CAUTION: Ballast is held in place by ignitor. Carefully remove the ignitor and the ballast together to avoid personal injury in case the ballast slides out of unit. Fixture Housing Ballast Ignitor Ignitor Retention Screw Lock Washer Reflector Reflector Screw (x5) 7. Dispose of used ballast assembly. 8. Connect the replacement ballast assembly following steps 1 through 7 in reverse order. Red Lamp Socket Photocell Socket Ballast Ignitor Red Red Black Black Blue Blue White White WhiteBlack WhiteBlack 120V AC Input 2 598-1235-01 Modelo SL-5679 Modelo SL-5679 Luz de patio del crepusculo al amanecer Instrucciones para la Instalacion LEA CUIDADOSAMENTE TODAS LAS INSTRUCCIONES ANTES DE EMPEZAR LA INSTALACION NOTA: Todo el cableado debe realizarse de acuerdo con el Codigo Nacional Electrico (Codigo Electrico Canadiense en Canada) usando tuberia u otro medio aceptable. Contactese con un electricista calificado si tiene alguna pregunta respecto a la adaptabilidad del sistema. La lampara en el dispositivo contiene mercurio. Desec...