Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
Read all instructions before beginning so you’ll be familiar with the parts and their final positions. MODEL #09500 ~ Cedar Sandbox (4’ x 6’) (Leaps and Bounds® #12956) TOOLS NEEDED: Phillips Screwdriver (power driver is helpful but be careful not to damage the product) PARTS INCLUDED: (A) 2 - 4’ Side Panels (B) 2 - 6’ Side Panels (C) 12 - Long Screws (D) 4 - Triangular Corner Seats (E) 16 - Short Screws NOTE: Sand is not included. You can purchase it separately from most home improvement and hardware stores. You will need approximately 600 pounds of sand to fill the sandbox 6” deep. If you want the sandbox to be deeper, assemble the sandbox and then mark the ground following the interior edges of the box. Move the sandbox aside and excavate within the marked area to the depth that you desire. Place the sandbox frame around the excavated area, and fill with the amount of sand desired. Remember, children should always wash their hands thoroughly with soap and water after playing in the sandbox, especially before handling snacks or meals. STEP 1: See PICTURE 1. All four corners assemble the same. Insert the dowel pegs on the edges of the 4’ SIDE PANELS (A) into the holes on the inside faces of the 6’ SIDE PANELS (B). This will line up the holes for the screws, and also it provides additional stability for the finished product. Secure the boards together using THREE LONG SCREWS (C) for each corner. The screws insert through the pre-drilled holes on the outside face of the 6’ sides. Be sure the screws are secured, but do not over torque or you may crack/splinter the wood. MAKE SURE that the pilot holes for the corner seats are facing up on all boards! STEP 2: See PICTURE 2. Attach one TRIANGULAR CORNER SEAT (D) to each corner of the sandbox using FOUR SHORT SCREWS (E) for each seat. The countersunk holes on the seats face up so the heads of the screws will be flush with the surface after being screwed in. Screw into the pilot holes pre-drilled on the 4’ and 6’ side panels. The SANDBOX is now assembled! An optional cover is available. It can be ordered from Leaps and Bounds® (Model #12957). A BC PICTURE 1 BADGER BASKET CO: TOLL FREE: 1-800-236-1310, parts1@badgerbasket.com D E PICTURE 2 Manufactured Exclusively for: Leaps and Bounds® 2.0/1108/TG ASSEMBLY INSTRUCTIONS Adult Assembly Required Save these instructions for future use BEFORE YOU BEGIN ASSEMBLY: Ensure that all the parts and hardware listed are included. If anything is missing or not satisfactory contact Badger Basket for assistance. Read all instructions before beginning so you’ll be familiar with the parts and their final positions. MODEL #09510 ~ Cover for Cedar Sandbox (4’ x 6’) (Leaps and Bounds® #12957) TOOLS NEEDED: Remember, children should always wash their Pliers hands thoroughly with soap and water after playingin the sandbox, especially before handling snacks or meals. PARTS INCLUDED: (A) 1 - Cover with 12 Attached The cover can be installed by one person. However, it is helpful to have one or two other people helping Snap Hooks to ensure you position the hooks where you want them so the (B) 12 - Eye Hook Screws cover is taut and even. STEP 1: See PICTURES 1 AND 2. Unfold the cover and lay it over the sandbox. One at a time, screw the eye hooks into the sides of the sandbox. The eye hooks may screw in easily without using tools. If a tool is needed, you can turn them with a pair of pliers. Do not rush. Work carefully to position each hook. Start with one corner, then do the corner diagonal to the first corner, and then complete the other two corners before doing the last four hooks. When the cover is attached, you want it to be taut, but not so taut that the fabric is stressed. If the fabric is too loose, rainwater and debris will pool on top of the cover. Attach the hooks onto the eye hooks all the way around the cover to secure the cover in place. Simply undo the hooks to remove the cover when you want to use the sandbox. The loose ties at one end of the cover can be used to roll it up and tie it. This sandbox cover is not designed to bear the weight of children or large animals. Do not let children crawl or walk around on the cover or jump on it. This will tear the fabric and/or the attachments and void any return policy or warranty offered on this item. PICTURE 1 PICTURE 2 2.0/1108/TG BADGER BASKET CO: TOLL FREE: 1-800-236-1310, parts1@badgerbasket.com Manufactured Exclusively for: Leaps and Bounds® ...