Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
The spa weighs approximately 2,339 pounds when filled with water. 6. Do not use the spa above a finished living area, due to the risk of water damage. 7. Be sure that there is room around the spa to permit servicing of the unit. The diameter of the tub is 69”. You should allow for this size, plus the size of the spa jet unit plus room to remove the cover, when choosing the location. 8. Be sure to note any other considerations, such as aesthetics or privacy concerns, that may affect the safety or enjoyment of using the spa. If you set up the spa outside: 1. You should check your local building codes concerning the use of outdoor spas. 2. The location must be close to an electrical outlet. An extension cord cannot be used with the spa. 3. The spa should be close to a source of water. 4. We recommend that you place the spa on a water and stain resistant, non-slip surface. 5. Be sure that the location you choose is stable. It must be able to support the weight of the spa when it is filled with water, plus the weight of the occupants. the spa weighs approximately 2,339 pounds when filled with water. 6. Think about environmental factors, such as rain, wind, shade, sunlight, and so forth. 7. You should be able to monitor the use of the spa from your home, to prevent unauthorized use by children. 8. Be sure that there is room around the spa to permit servicing of the unit. The diameter of the tub is 69”. You should allow for this size, plus the size of the spa jet unit plus room to remove the cover, when choosing the location. 9. Be sure to note any other considerations, such as aesthetics or privacy concerns, which may affect the safety or enjoyment of using the spa. 6 1. Before beginning assembly, be sure that you have read and understand the information in the box above and on page 6. Place the Surround Bottom (45) and the pre- attached Spa Surround (9) on the ground in the location you have chosen for assembly. Unfold the Spa Surround until it is round. Open the Inflatable Liner (29). Lay the floor of the Inflatable Liner (the side with the triangular pattern) on the bottom of the Spa Surround (9). Pull the liner wall up, making sure that the three indicated holes in the Inflatable Liner are centered in the cutout in the Spa Surround. 1A 29 Before beginning assembly, carefully read the following information and instructions: • Place all parts in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. • Read all assembly steps before you begin. • Assembly requires only the included air pump. Note: The included flat wrench is not required for assembly. The flat wrench is used to remove the filter cap (see pages 10 and 11). • Make sure that all parts are oriented as shown in the drawings. 9 45 Holes Cutout Fastener Strip Assembly 1B 9 29 Flap Fastener Strip Cross Section View from the Outside Cutout Holes in Inflatable Liner 1A 29 Before beginning assembly, carefully read the following information and instructions: • Place all parts in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. • Read all assembly steps before you begin. • Assembly requires only the included air pump. Note: The included flat wrench is not required for assembly. The flat wrench is used to remove the filter cap (see pages 10 and 11). • Make sure that all parts are oriented as shown in the drawings. 9 45 Holes Cutout Fastener Strip Assembly 1B 9 29 Flap Fastener Strip Cross Section View from the Outside Cutout Holes in Inflatable Liner Attach the flap on the top edge of the Inflatable Liner (29) to the fastener strip on the edge of the Spa Surround (9). Start the flap where the fastener strip starts and pull the flap tight as you go around. Make sure the three holes in the Inflatable Liner are centered in the cutout in the Spa Surround (9), as shown in the inset drawing. 7 2. Orient the dry side jet pack (A) as shown and place it near the three holes in the Inflatable Liner (29). Slide the Temperature Probe Gasket (46) over the connector threads on the Temperature Probe Assembly (30). Insert the wire (not shown) through the small hole in the Inflatable Liner (29) and then push the Temperature Probe Assembly into the hole. Make sure that the threads on the connector are pushed fully through the vinyl liner. Firmly tighten the Temperature Probe Nut (47) onto the connector threads. Connect the wire from the Temperature Probe to the receptacle on the dry side jet pack (A). 3. Move the dry side jet pack (A) against the wall of the tub. Pull the two connectors on the dry side jet pack through the large holes in the Inflatable Liner (29). Slide a Wet Side Gasket (48) onto each connector. Firmly tighten a Wet Side Nut (49) onto each connector. 4. Position the wet side jet pack (B) as shown. Place an O-ring (52) in the groove of each connector on the wet side jet pack. Make sure that the O-rings are positioned securely in th...