Votes - 2, Average rating: 4
(
)
)
|
manual abstract
For information and supplies to maintain the beauty and color of your premium cedar surround, contact your local pool and spa supply store. CLEANING THE SPA SHELL The spa shell should be cleaned with a mild soap solution; do not use solvents or waxes. The spa should always be clean and dry before being moved or stored. The filters should be checked periodically for build-up of dirt and oil. If the filters need to be cleaned, follow the steps below: 1. Turn off the power. 2. Unscrew the filter covers. 4. Lift the the filters out of the filter housings. 5. Check the filters for dirt and debris. If the filters need to be cleaned, rinse the filters with a hose. If the filters are still dirty, soak them in cleaning solution from a pool and spa Filter Housing Filter Filter Cover supply store. 6. Inspect the filters for damage. Replace the filters if the are damaged. 7. Insert the cleaned or new filters into the filter housings. 8. Re-attach the filter covers. WATER CHEMISTRY Maintaining the pH level of the water is very important to the operation of the spa. To maintain the proper pH level and to sanitize the spa, you can purchase a chemical starter kit from your local pool and spa supply store. CAUTION: The chemicals used to maintain the pH balance of the water and to sanitize the water can be dangerous. Always follow these basic guidelines when handling the chemicals: 1. Always read and follow the directions on the label, unless directed otherwise. 2. Never mix different chemicals. 3. Do not exceed the recommended amounts of chemicals—follow the directions on the label. 13 4. Keep all chemicals out of the reach of children and pets. 5. Keep all containers closed tightly when not in use. 6. Never add water to the chemicals—always add the chemicals to the water as directed. 7. Always store chemicals in a cool, dry place. MAINTAINING THE PROPER PH BALANCE The pH factor is a measure of the relative acidity or alkalinity in the water, and is measured on a scale of 1 to 14. Pure water has a value of 7, which is neutral. Any value above 7 is alkaline, and any value below 7 is acidic. You should maintain a slightly alkaline pH level, between 7.2 and 7.8, in the hydrotherapy spa. Severe problems can occur when the pH balance is not maintained within this range. If the pH level exceeds 7.8, dissolved minerals can build up and clog the plumbing in the spa jet unit. If the pH level falls below 7.2, the acid level in the water will begin to corrode the metal parts in the spa jet unit. Also, the sanitation agents in the water will not be effective if the pH level is not properly maintained. Damage caused by improper pH levels is not covered under the warranty. To maintain the proper pH level, test the pH of the water regularly. To test the water, purchase a pH test kit at a pool and spa supply store. The pH reading should be between 7.2 and 7.8. If the level is too low, add a pH increaser (usually soda ash). If the level is too high, add a pH reducer (usually sodium bisulfate). Test the water again after five minutes. See the instructions with your pH test kit for additional information about testing and adjusting the pH. SANITIZING THE HYDROTHERAPY SPA The most common sanitizing agent is a solid bromine concentrate. The amount required varies according to several factors, such as user load, temperature, and water conditions. Proper water maintenance is a complex process. Contact your local pool and spa supplier for information concerning which chemicals you should use in your area to sanitize the spa. CHANGING THE FILTER CYCLE The spa will filter the water every 12 hours. The duration of the cycle can be adjusted to last 2 to 5 hours. Press the temperature up or temperature down button on the console. When the display begins to flash, press the pump button. The display will read F2. To change the time, press the temp up button until the desired time is reached. Press the pump button to confirm the selection. As spa usage increases, the duration of the filter cycle may need to be increased. ATTACHING AND REMOVING THE ACCESS PANEL Turn off the spa power. To remove the indicated Access Panel (25), Remove the four 1/4” x 20 x 1 1/2” Machine Screws (46) that secure the Access Panel to the spa. Carefully remove the Access Panel and set it aside. 25 46 46 To replace the Access Panel, hold the Access Panel in place and secure it with the 4 1/4” x 20 x 1 1/2” Machine Screws (46). Be careful not to overtighten the Screws. DRAINING THE HYDROTHERAPY SPA The hydrotherapy spa should be drained at least four times per year and refilled with clean water. You may need to drain the spa more often, depending on the user load. This must be done because after repeated chemical treatment the water becomes chemically saturated. Once this happens, additional chemical treatment of the water is no longer effective. The spa should also be drained if you will not be using it for long periods of time. The spa must always be drained before major repairs...
Other models in this manual:Other Home Accessories - IMSG73911 (537.12 kb)