Votes - 5, Average rating: 4.6
(
)
)
|
manual abstract
The Rough-In Box allows the panel to be mounted directly to the studs/ pre-wall and includes a wall box and mounting screws. Wall Mount panels (NXDs) are contained within a metallic outer housing (back box). This back box is not removed when installing the NXD into a Rough-In Box. The back box is only removed to gain access for the replacement of the Compact Flash component or upgrade to the VESA housing. Specifications CB-TP5 (FG038-10) Specifications Dimensions (HWD) • 3 3/4” x 5 1/4” x 3 3/8” • 9.6 cm x 13.3 cm x 8.6 cm Included Accessories • 4 Phillips pan-head (#4-40 x 0.375 Black) screws (80-0115) • 4 Phillips pan-head (#4-40 x 0.625 Black) screws (80-0118) Certifications • cTUVus Listed WARNING: INSTALLER, LEAVE A GAP BETWEEN THE STUD AND ROUGH-IN BOX TO ACCOMMODATE THE DRYWALL/SHEETROCK. This gap allows the installation of the drywail/sheetrock after the CB-TP5 has been mounted onto the beams. The rough-in box installation must be done prior to any wall installation. Note: The most important thing to remember when mounting this rough-in box is that the mounting tabs must be mounted flush against the outside of the sheetrock. It is recommended that you cut out the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments. The wiring knockouts on the left side will be used for the NXD-CV5 Wall Mount panel connectors, so always secure the rough-in box to the stud using the Stud Mounting Holes on the right side of the box. Pre-Wall Installation of the CP-TP5 Rough-In Box • Refer to the SP226101 diagram for detailed installation dimensions. • Cutting out the surface slightly smaller than what is outlined in the installation drawings, in order to make any necessary cutout adjustments, is highly recommended. • The wiring knockouts on the left side will be used for the NXD-CV5 Wall Mount panel connectors, so always secure the rough-in box to the stud using the Stud Mounting Holes on the right side of the box. Rest the right Stud Mounting tabs onto the stud (keeping the knockouts on the left). Be sure to leave enough of a gap between the stud and NXD Mounting tabs to accommodate the installation of the drywall or sheetrock after the rough-in box has been mounted. Ultimately, the Mounting Tabs should lie flush against the outside of the sheetrock. Fasten the CB-TP5 rough-in box to the stud through the holes on the right Stud Mounting tabs (FIG. 1), using either nails or screws. 3. Remove the wiring knockouts from the left side of the CB-TP5 to accommodate the cables being threaded through to the NXD touch panel. Note: Remember that when mounting this rough-in box, the NXD mounting tabs must lie flush against the outside of the sheetrock. 4. Thread the incoming power, RJ-45 audio/video, Ethernet, and USB wiring through the knockouts (use of the left wiring knockouts are recommended with this installation). Leave enough slack in the wiring to accommodate any repositioning of the panel. 5. Install the drywall/sheetrock before inserting the main NXD unit into the CB-TP5. .671 I i 7, 04 1-(- 2 600 166.04) Top Do Not Use These Tabs To Mount Rough-In Box Bottom ■5 Ml ( 130.593 - 2X 1.942 1 49.3U 3.868 198,251 (==> upî <==on"t 871 [22.121 f—- 3.400 186.361 - Do Not Use These Tabs To Mount Rough-In Box 4.071 [103.4] - 2X 2.225 156,52] - 21 2 600 (66.041 2 742 [69.631 Left e 2X I 175 129.851- r 2X 789 120,03) 2X .789 [20.03] 2t 5 065 [128,65] 2X 5 065 1128.65) vQ 0 200 (5.08) -HAILING HOLES TABS ONI Y TYP 2X 2 225 [56,521 o o □ -O o. 4.276 1108,631 Right — 2K 1.175 t29,85) For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s). 10/08 ©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time. 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical sup...