Votes - 2, Average rating: 5 ( )

Manafacture: Dometic File size: 448.52 kb File name: 884d38f0-8eae-47df-af4a-d33d5e242d3b.pdf Language of manual:

Modification of this product can result in property damage. Dometic Corporation • Sanitation Systems 13128 State Rt 226, PO Box 38 Big Prairie, OH 44611 SeaLand Product Customer Service: 1-800-321-9886 (8:00 a.m. - 5:00 p.m. ET) 2 TABLE OF CONTENTS Toilet Model Identification . . . . . . . . . . . . . . . . 2 Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . 2 Concerto Toilet Dimensions . . . . . . . . . . . . . . . 3 Toilet Installation Instructions . . . . . . . . . . 3 - 6 Remote Flush Switch Installation . . . . . . . . . . 7 Important Information Before Operation . . . . . 8 Electronic "Flush and Forget" Operation . . . . . 8 Toilet Controls . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating Instructions . . . . . . . . . . . . . . . . . . . 9 Automatic Flush Operation Timing Chart . . . . 9 Proper Cleaning and Maintenance . . . . . . . . 10 Manual Flush Operation . . . . . . . . . . . . . . . . 10 Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Deodorants and Special Tissue . . . . . . . . . . 11 Flush Mechanism Components . . . . . . . . . . . 12 Electrical Specifications . . . . . . . . . . . . . . . . . 13 Troubleshooting . . . . . . . . . . . . . . . . . . . 14 – 17 Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . 18 Customer Service . . . . . . . . . . . . . . . . . . . . . 19 Limited Warranties . . . . . . . . . . . . . . . . . . . . 20 WARNING – ELECTRICAL SYSTEM. Turn off electrical power before servicing. WARNING – MOTOR STARTS AUTOMATICALLY. Turn off electrical power before servicing. Read and understand the complete contents of this manual before operating or servicing the toilet. Failure to follow these precautions may result in damage to the toilet. TOILET MODEL IDENTIFICATION The model identification label is located on the inside wall of the toilet under the access cover. It will show the model number and serial number. DOMETIC CORPORATION P.O. BOX 38, 13128 STATE RT 226 (800) 321-9886 BIG PRAIRIE, OH 44611 USA MODEL NO. 000 SERIAL NUMBER 000000 ORDERING PARTS Dometic is ready to assist you in the event service is required. Before calling, please have the following information available. Your cooperation in having this information ready is appreciated and allows us to better meet your needs. Please refer to the Parts Distributor list in the Customer Service section. 1. Toilet Model Number 2. Serial Number 3. Part Number, Description and Quantity (see Parts List) Concerto, SeaLand and Flush and Forget are registered trademarks of Dometic Corporation. CONCERTOTM TOILET DIMENSIONS Dimensions may vary ±3/8-inch (13mm). TOILET INSTALLATION INSTRUCTIONS System Requirements: • 2 GPM (10.6 lpm) or larger water pump. • 1/2-inch (12.7 mm) water line terminating in 1/2-inch MPT fitting (to connect to toilet water supply hose). • 4-bolt floor (closet) flange. SeaLand flanges available include 3-inch spigot, socket, MPT, or 45-degree swivel socket. • 12 VDC through 7- or 8-amp fuse or circuit breaker. Use 14-gauge stranded copper wire. IMPORTANT: If replacing an existing gravity-discharge toilet, make sure the center of the existing discharge flange is at least 11-1/4 inches from the back wall, then proceed to Step 5 for proper positioning of water line and electrical wiring. STEP 1: Carefully unpack the toilet bowl, rear access lid and floor flange adapter. CAUTION: HANDLE THE VITREOUS CHINA TOILET AND ACCESS LID WITH CARE. SET THE LID IN AN AREA WHERE IT CANNOT BE BROKEN. PLACE LID ON TOILET ONLY AFTER TOILET INSTALLATION IS COMPLETE. STEP 2: Position the china bowl in the space intended. Confirm that adequate clearance is available for using the flush handle and opening the seat and lid. STEP 3: Mark the floor at the rear corners of the toilet bowl (fig. 1). Measure the distance between the two marks and divide by 2 to find the toilet centerline. Mark the floor at the rear wall for the centerline. STEP 4: Place a carpenter’s square against the back wall, and draw a center line on the floor at least 14 inches (356 mm) long (fig. 2). Mark the centerline for the floor flange at 11-1/4 inches (286 mm) from the wall (fig. 3). Fig. 3 Fig. 1 Fig. 2 STEP 5a: For through-the-floor water line and electrical wires, mark another centerline 6 inches (152 mm) from the back wall (fig. 4). STEP 5b: For through-the-wall water line and electrical wires, mark a centerline 8 inches (203 mm) up from the floor centerline (fig. 5). STEP 6: Make a 4-3/4 inch (121 mm) diameter hole (for most floor flanges) or a 5-1/8 inch (130 mm) diameter hole (for swivel joint floor flange) at the centerline mark furthest from the wall. Make a 1 inch (25 mm) hole at the mark closer to the wall for the water line and electrical wires (fig. 6). IMPORTANT: The prefered floor flange installation method is to mount the floor fIange directly on the finished floor. However, if the bottom of floor flange and bottom of china ...

Download now

Please, enter two numbers from picture: