Votes - 4, Average rating: 4.5 ( )

Manafacture: Arrow Storage Products File size: 1.91 mb File name: Language of manual:

3 Fasten the sidewall angles across the inside top of the side panels using screws. Side wall angles must overlap rear wall angle in corners. 4. Fasten the side wall channel assemblies across the middle of the side panels using screws. Fasten overlaps in rear corners with screws. 5 Fasten the door track assembly (holes on top) across the top of the front wall panels using screws. See the figu re. 9366 \ l _on t """_..-.,_ _ Long Leg Top Opening Facing in Short Leg on Bottom The wall NOTE channels behind the front wall panels will be installed in a later step. i 2O ® Parts Needed For ® 0 8995 Wan Panel (8) Step 8 Wall Panels L]N21 Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the panel that follows it. 1 Locate all of the wall panels and set each one alongside the building. 2 Be surethatyou have the correct panels in each position. Do this by overlapping the panels and determining if the holes line up with the holes in the frame. 3 Fasten the wall panels at the top and bottom with screws. 4 Fasten the center of each panel to the wall channel with screws. Fasten overlapping ribs using a bolt and nut with two screws. 5 When you have attached all wall panels in the correct positions, the building will look like this. [Z] 8995 8995 Panels rest on frame as shown 8995 Crimped Rib Underneath Detail Showing Center of Panel Screwed to Wall Channel Bolt and nut does not go thru wall channel at overlap Use bolts and nuts thru wall angle overlap at the top of panel at rear. ® Parts Needed For ® • 9900 Door Jamb (2) • 9365 Front Wall Channel (2) Step 9 Front Channel/Door Jamb UN22 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both doorjambs. 1 Fasten the front wall channels in their positions between the end of the side waft channel and the corner panel using screws. Do not put a screw in the hole at the end be hind the door opening at this time. 2 Fasten a door jamb to the front panel with two bolts, nuts and acorn nuts, as shown. 3 Fasten the center of the door jamb to the front wall panel and the front wall channel with two screws. INSIDE OF BUILDING (2) Acorn Nut \ Front Wall Channel Hex Nut Cross-Section ",,,,., Top View Acorn Nut 9900 Screw DoorTrack Screw 4. Fasten the top of the doorjamb to Screw the door track with two screws. Do the same for the bottom into frame. Repeat steps 2 through 4 for the opposite door jamb. ® Parts Needed For ® • 6000 Right Gable (2) O 6001 Left Gable (2) Step 10 Gable Assemblies O 5971 Roof Beam Bracket (4) _23 The gables go on top of the front and rear walls to support the roof beams. r NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. 1 Attach the four roof beam brackets to the gables using two bolts, washers and nuts. NOTE Mounting leg of bracket must face toward center of gable and holes closest together must be on top 5971 Roof Beam Brackets 6001 ® Parts Needed For ® • Left Gable Assemblies (2) • Right Gable Assemblies (2) Step 11 Gables/Braces • 6635 Gable Brace (2) A24 1 Lift and fasten a right and left gable, under angle at corner, to the door track and rear wall angle with screws. Hint: On the rear gable, use a bolt and nut at the overlapping rear wall angle. On the front gable, leave out 2 screws closest to center gable leg. 2 Join the left and right gables together with a gable brace using a bolt and nut in the bottom hole only. 3 Repeat Steps 1 & 2 for the door track on the front of building, except for the track supports, fasten as shown. ble Brace pports 6228 St A25 ep 12 ® Parts Needed For ® Roof Beams e aain RoofBeam(1) • s_,,g_eRoofBeam(2_ "1 Spread the two halves of the main roof beam and fasten the roof beam to the gable brace of the front gable. 2 Fasten the other end of the main roof beam to the gable brace of the rear gable. Single Roof Beam Assembly 3 Fasten the single roof beams, small holes on top, as shown using bolts and nuts. Spread Two Halves Of Roof Beams Main Roof Beam Assembly ® Parts Needed For ® O 6640 Right Roof Panel {1) Step 13 Right Roof Panel $26 Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of the building. Each screw and bolt in the roof requires a washer. NOTE Measure the building diagonally again and make adjustments to make sure the building is square. This will make the roof panels fit better, and holes will align. NOTE If a Roof Beef=Up Kit was purchased, assemble prior to attaching the roof panels. 1 Locate all the roof panels by their numbers and place them on the ground alongside the building in their proper positions. 2 Position a right roof panel at the back right corner and fasten to the gable and roof beams using screws and bolts and nuts as shown. Do not fasten the lower end of the panels to the side waft angles at this time. Hint: Follow the fastener sequence shown, for proper alignment. 6641 6640 65...

Download now

Please, enter two numbers from picture: