Votes - 5, Average rating: 4
(
)
)
|
manual abstract
Finished Deck Material Whirlpool Framing Material Water- Resistant Deck Material Wall Material Tile Whirlpool Brick Approved Tile Backing Apply silicone sealant to the edges of the water- resistant deck material and the finished deck. Apply sealant Alcove Installation Drop-In Installation Concrete Installation Tile Kohler Co. 13 1019749-2-M 17. Confirm Proper Operation FilltheWhirlpoolNOTE:Please read these steps carefully before you operate your whirlpool. Position the jet nozzles so they face down toward the basin. Turn the jet trim rings fully counterclockwise. Fillthewhirlpooltoawaterlevelatleast2.(51mm)abovethetopofthehighestjet. NOTE:The water temperature in the whirlpool should not exceed 104°F (40°C). The heater will automatically turn off as the water temperature approaches 104°F (40°C) and will remain off until the water cools. 18. Operating Sequence Models without Neckjets NOTE:A built-in heater automatically helps to maintain the water temperature when the whirlpool is running, as long as the water temperature does not exceed 104°F (40°C). The heater will disengage at higher temperatures. IMPORTANT!Please refer to your Homeowners Guide for detailed instructions on the user keypad and optional remote control. Press the Power On/Off button to turn on the whirlpool. The whirlpool will start at medium flow. Increase or decrease the water flow by pressing either the up or down arrow buttons on the keypad. An indicator bar in the center of the keypad shows the water flow volume. Adjust each jet for optimum air/water mixture. Turn the jet trim clockwise to reduce the air flow, and counterclockwise to increase the air flow. Press the heater button to turn the heater off and back on. When illuminated, the indicator light shows that the water temperature will be maintained up to 104°F (40°C). Press the Power On/Off button a second time to turn the whirlpool off. NOTE:A built-in timer automatically stops the pump and motor after approximately 20 minutes of operation. Models with Neckjets Heater On/Off Decreases Flow Increases Flow Flow Mode Increases Flow Power On/Off Decreases Flow Lighted User Keypad (for whirlpools without neckjets) Lighted User Keypad (for whirlpools with neckjets) Heater On/Off Power On/Off Heater Indicator Light Indicator Bar - Shows water flow volume Activates Mode Selected Neckjet Mode - Adjust Pulse Turn the jet trim clockwise to decrease the flow. Turn the jet trim counterclockwise to increase the flow. Position the jet nozzles so they face down toward the basin. Turn the jet trim rings fully counterclockwise. Fillthewhirlpooltoawaterlevelatleast2.(51mm)abovethetopofthehighestjet. NOTE:The water temperature in the whirlpool should not exceed 104°F (40°C). The heater will automatically turn off as the water temperature approaches 104°F (40°C) and will remain off until the water cools. 18. Operating Sequence Models without Neckjets NOTE:A built-in heater automatically helps to maintain the water temperature when the whirlpool is running, as long as the water temperature does not exceed 104°F (40°C). The heater will disengage at higher temperatures. IMPORTANT!Please refer to your Homeowners Guide for detailed instructions on the user keypad and optional remote control. Press the Power On/Off button to turn on the whirlpool. The whirlpool will start at medium flow. Increase or decrease the water flow by pressing either the up or down arrow buttons on the keypad. An indicator bar in the center of the keypad shows the water flow volume. Adjust each jet for optimum air/water mixture. Turn the jet trim clockwise to reduce the air flow, and counterclockwise to increase the air flow. Press the heater button to turn the heater off and back on. When illuminated, th...
Other models in this manual:Other Home Accessories - K-1014 (2.57 mb)
Other Home Accessories - K-1110 (2.57 mb)
Other Home Accessories - K-1158 (2.57 mb)
Other Home Accessories - K-1170 (2.57 mb)