Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
Please refer to this guide for instructions on how on use of the CD player. Dealer Installation This section intended for use by authorized dealer personnel only Getting Ready To Start The Sonic Immersion System can only be installed on spas with the following serial numbers. Table 1 Sonic Immersion System Ready Spas Model Serial Number Aurora HP 91275 or higher Aurora II 91210 and higher (Also 91184) Aurora XLT 91295 and higher Caliente HP 91301 and higher (Also 91290 and 91299) Californian 91198 and higher Chairman 91245 and higher Chairman II 91234 and higher Diplomat 91197 and higher Nautilus 91458 and higher (Also 91455) Triad 91372 Triad II 91625 an higher (Also 91567) Overview of the Installation The installation of the Sonic Immersion System is a simple process that includes removing the spa skirt, drilling a few holes using the templates provided to guide you, and then connecting one or more power cables. This guide is provided to help complete this task in a quick and efficient manner. Required Tools You will need the following tools to complete the installation: Table 2 Required Tools Electric drill 1 . inch (3.8 mm) hole saw . inch (6.35 mm) drill bit 3/8 inch (9.5 mm) drill bit Saber Saw Phillips screwdriver Tape (masking, electrical, duct, or packaging) . in (12.7 mm) width Spring-loaded punch (or other tool(s) that can be used to mark drilling locations, such as a hammer & nail) Fine Point Marker Measuring Tape Fish Tape Fish Tape Lubricant Non Ratcheting PVC Pipe Cutter Medium Size Needle Nose Pliers Wire Stripper Utility Knife 5/16” (7.94 mm) Nut Driver or wrench Six inch (15.24 cm) square Stapler and Staples Straight Edge Safety Glasses Silicone caulking (clear) Small Saw Parts List You should have received the following parts in the Sonic Immersion System installation kit: Table 3 Parts List Description Qty Item Number This document 1 01510- 1030 Amplifier 1 01564-08 Coarse- Threaded Drywall Screws 5 01051-06 Template 1 Doc 74- Rev A Power Supply Harness 1 01564-19 Power, supply, stereo 1 01564-01 Main Harness 1 01564-20 Speaker, lead 2 01564-21 Speakers, Satellite 2 01564-14 Stereo 1 01564-03 Sub-woofer sub assembly 1 01564-09 Stereo cover, marine 1 01564-04 Dual pole antenna 1 01564-05 Preamp stereo, cable 2 01570-24 Power supply screw, sheet metal, SS, PH 2 01011-38 Marine cover screws, #8 x .” (1.3 cm) SS Truss Head 4 01011-40 Cable Ty, 4” (10.2 cm) black 10 01200-006 Cable Ty Mount 10 01200-005 Removing Panels In order to install the system up to three panels must be removed from the spa: the equipment compartment panel, the panel where the sub woofer is installed, and the panel where the Satellite Speakers are to be installed. Remove Equipment Compartment Panel Warning Possible Electrical Shock Hazard 1. Turn off the main spa circuit breaker located in the disconnect box or house panel. 2. Verify that all power has been turned off before continuing installation. Note Refer to the Spa Service Manual to determine how to confirm that all power to the spa has been turned off. 3. Locate the spa’s Main Top Side Control, Figure 1. Figure 1. Top Side Control 4. The Lower Control is located in the equipment compartment behind the spa panel below the Main Top Side Control. 5. Use the screwdriver to remove the equipment compartment panel screws, Figure 2. Figure 2. Equipment Compartment Panel Screws Note The number of screws to be removed will depend on the model of spa. Remove the Sub Woofer Compartment Panel The installation location of the sub woofer compartment will vary from one spa model to another. Use Table 4 to locate the compartment on your spa. First, stand in front of the spa facing the Top Side Control (at the 6 o’clock position, see below) and then refer to Table 4 below. Sub-Woofer Installation Locator Top Side Control Table 4 Model List Model and Number Location of Installation Aurora II and Chairman Top Side Control Chairman II and Aurora XLT Top Side Control Diplomat, Californian Top Side Control Nautilus Top Side Control Caliente HP, Triad II, Aurora HP, and Triad Top Side Control 1. Use the screwdriver to remove the spa panel screws, Figure 3. Figure 3. Equipment Compartment Panel Screws Note The number of screws to be removed will depend on the model of spa. Installing the Sub Woofer Compartment The installation of the sub woofer compartment consists of removing the panel, removing the paper cover, exposing the plug, removing the plug, and installing the sub woofer compartment. 1. If you have a spa with wood siding you may skip to Step 2. If your spa has EnviroTect. siding you will need to remove the white foam sheeting, Figure 4. Figure 4. Removing EnviroTect. Sheeting 2. Using a locking utility knife set for a depth of about . inch, cut a 13” X 18.5” (33 cm X 47 cm) rectangle as shown in Figure 5. Remove the paper and foam until you expose the sub woofer plug. You may need to use a screwdriver or other tool to remove the paper and foam. Figure 5. Cutting Rectangle Note T...