Avoid any hidden pipes or wiring in the ground. Be aware of where you are inserting the Ground Stake (16) of the Solar Candle Garden Lantern. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its REV 07d intended function. Any broken parts or mounting fixture that may affect proper operation should be properly repaired or replaced by a qualified technician. Properly disponse of any used batteries. Dispose of the used batteries properly according to the solid Waste disposal regulations in your community. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 7. Before using, you need to charge the batteries. You can do this by placing the Solar Lantern in the sunlight. The Lantern will take approximately 8 hours of sunlight to charge. Be sure the four Solar Panels (2) are in full sunlight. FIGURE 1Top AssemblyPlastic Ring (11) Solar Panels (2) After the Batteries (8) are charged, remove the Top Assembly (See Figure 1) by twisting counterclockwise off the Plastic Ring (11) and lifting it off the Lantern. Power Switch (18) Battery (8) Plastic Ring (11) FIGURE 2The Power Switch (10) is on the underside of the Top Assembly. To have the light turn on at night, locate the Power Switch (18) and switch to the ON position. You can turn the Solar Candle Garden Lantern Power Switch (18) OFF if you do not want the light to turn on at night. See Figure 2. Replace the Top Assembly by connecting it to the Lantern, matching up the notches and twisting clockwise for closure. “S” Steel Tube (19) Small Loop (1) Ground Stake (16) FIGURE 3Middle Steel Tube (22) The Shepherd’s Hook is screwed together with three threaded shafts (19, 22 and 23). Hook inserts into the top of the Ground Stake (16) and the Lantern hangs from the Lower Steel Tube (23) hook by a Small Loop (1) at the top of the light. See Figure 3 and Assembly Drawing on page 7. Choose the location for the Solar Candle Garden Lantern and stick the Shepherd’s Hook and Ground Stake (16) into the ground, avoiding any underground wiring or plumbing. Be sure to choose a location that gets plenty of sunshine during the day and is not near a porch or street light at night. See Figure 3. If the Solar Candle Garden Lantern stops working or is not holding a charge for a long enough period, replace the batteries with identical rechargeable NiCd “AA” batteries. See directions below for battery replacement. FIGURE 4Small Loop (1) Note: The Solar Candle Garden Lantern can be removed from the Shepherd’s Hook and Stake and used as a table Lantern. See Figure 4. BATTERY REPLACEMENT Turn the Top Assembly of the Solar Candle Garden Lantern slightly counterclockwise. Remove the assembly from the top of the Solar Candle Garden Lantern. See Figure 1 on page 3. Take assembly off the Lantern, being careful not to disturb the wires and the internal components. See Figure 2 on page 4. Remove the used Batteries (8) and dispose of them properly according to the Solid Waste Disposal regulations in your community. Replace with new Rechargeable NiCd Batteries (8). The polarity of the batteries is marked inside the Battery Case (10). Be careful of the internal components and do not disturb the wires. Once the batteries are in place, match up the notches and return the Top Assembly. Twist clockwise onto the Plastic Ring (11). Then tighten. Note: Test that the Top Assembly and Lantern are secure before hanging on the Shepherd’s Hook. Maintenance WARNING! Make sure the Power Switch (18) of the Solar Candle Garden Lantern is in its “OFF” position before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of the Solar Candle Garden Lantern. Check for loose screws, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. Do not use damaged equipment. 3. Clean the outside of the Solar Candle Garden Lantern with a clean and damp cloth. Never use abrasive cleaners; they will damage the unit. You may use a mild detergent. Never submerge the Solar Candle Garden Lantern in water or any other liquid. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufactur...