Votes - 4, Average rating: 3.3
(
)
)
|
manual abstract
A Kit Includes: Installation: 1. Remove the original bulb connector from the back side of the housing. 2. Remove the tail light housing from the vehicle. 3. On the Chevelle, remove the chrome tail light cover. There are four nuts on the back side of the housing. 4. Remove the tail light lens. On the Camaro there are five screws and one metal clip on the back side of the housing. 5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7. Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8. Feed the wires through the large hole in the back plate and attach the back plate onto the back side of the housing. The flat side of the mounting disk should be toward the outside and the side with the slight raised center should go in toward the housing. This will align the mount in the original housing. 9. Secure the back plate with the supplied #6 lock nuts. 10. Make sure the original lens gasket is in place and replace the tail light lens. 11. Replace the chrome trim and then tighten down carefully. 12. Cut off the existing light socket as it will not be used. Do not strip the wires. Trim the wires from LED assembly to appropriate length once mounted, making sure wires are routed cleanly and securely. 13. Use the supplied moisture resistant pigtail connectors* to attach the wires from the new LED assembly to the existing vehicle harness. Insert appropriate wire from vehicle harness and mating LED assembly wire into a connector and crimp following instructions below. *For the best connection, soldering is recommended. But to simplify installation, the supplied connectors will provide a fast weather resistant connection. The correct crimp method for the supplied connectors is: 1.) Insert UNSTRIPPED wires into the connector and ensure they are all they way in by observing the clear bottom of the connector to see the wires are touching the end. 2.) Use pliers to push the blue cap down flush with the edge of the clear body, completing the connection. The connection will only be correct if pressed firmly down with pliers. Attach to metal boltorscrewfor Ground connectionwithmetal housings OR GREEN wireBROWN wireBLACK wirefrom LED from LED from LEDassembly assembly assembly BLACK wireTurn Signal wireTail Light wireGround wire fromvehicle from LEDfrom vehicle fromvehicle harness assemblyharnessharnesswith plastic housings LED wiresVehicle harnessTail lightBrownBrown or BlackDriver’s TurnGreenGreen orPinkPassenger’s TurnGreenYellow or PurpleGroundBlackChassis or body 14.Repeat forthe otherside. 15.Test the tail lights, brake lights, and turn signals. Ifthe turn signals do notflash you will need to upgrade yourflasher. If you are replacingonly the rearturn signals a heavy duty electronicflasher from your localparts storeshould be able to be used.If you are replacing bothfrontand rear or do nothave front bulbs you will need a no-loadflasher,Dakota Digital part numberLAT-NLF. SERVICE AND REPAIR DAKOTA DIGITAL offers complete service andrepair of itsproduct line.In addition, technicalconsultation isavailable to help you work through any questions orproblemsyou may be having installing one ofour products. Please read through the Troubleshooting Guide. There,you willfind the solution to most problems. Shouldyou everneedto send the unit back for repairs,please callour technicalsupport line,(605) 332-6513,to requesta Return MerchandiseAuthorizationnumber.Package the productin a good quality boxalong withplenty of packing material.Ship the productby UPSor insured Parcel Post.Be sure to include the RMAnumberon the package, and include a complete description ofthe problem with RMA number, your full name and address (streetaddresspreferred), and a telephone number where you can be reached during the day.Any returns forwarrantywork must include a copyof the dated salesreceipt fromyourplace of purchase.Send no money.We will billyou after repair. Dakota DigitalLimited LifetimeWarranty DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this productthat should it, under normal use and condition, be proven defective inmaterial orworkmanship for the lifetime ofthe original vehicle itwas installed in, such defect(s)will be repaired orreplaced at Dakota Digital’s option. Thiswarrantydoes notcovernor extend to damage to the vehicle’ssystems, and doesnotcover removal or reinstallation of the product. ThisWarrantydoesnotapplyto any product or partthereofwhich in the opinion of the Companyhasbeen damaged through alteration, improper installation, mishandling, misuse, neglect,oraccident. ThisWarranty is in lieu ofall other expressed warrantiesor liabilities. Any implied warranties, including any implied warranty of merchantabi...