Votes - 3, Average rating: 3
(
)
)
|
manual abstract
• Clear an area large enough to layout all components and hardware. • When applicable, tighten all hardware connections by hand first. Once the step is completed go back and fully tighten all hardware. • Follow all steps in order to properly assemble your product. To complete assembly you will need: • (1) Leak Detection Solution (Instructions on how to make solution are included in “Operating Instructions” section) • (1) 14.1 oz LP gas tank. Note: You must follow all steps to properly assemble grill. Typical assembly: approximately 5 minutes. 3 Attach Mantles Insert Globe Note: Tie the mantles around grooves in burner. Note: Evenly distribute folds on mantle. Cut off the extra string. 4 page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. 5 Attach Cap 6 Attach LP Gas Tank 7 Insert Into Base Outdoor LP Gas Lantern Model No. GLL800W Operating Instructions Figure 1 Caution: If burner flame goes out during operation, immediately turn This lantern is designed to operate with a one pound the gas “OFF” and let the gas clear for about 5 minutes before re 7-3/8” high disposable / 16.4 oz. or 14.1 oz. propane gas tank (DOT 39 Cylinder). lighting. DO NOT ATTEMPT TO REFILL ANY ONE POUND (16.4 oz. or 14.1 oz.) PROPANE GAS TANKS! Turning Off 1. Turn control knobs to the “OFF” position. Connecting Gas Tank 2. Remove LP gas tank and properly store tank. 1. Make sure the control knob is in the “OFF” position. (Figure 1) Transporting 2. Lubricate the threads of the regulator valve While Lantern is ON with petroleum jelly, insert the gas tank into the regulator valve and hand-tighten firmly. (Figure 2) 1. Carefully carry the lantern by the handle. Figure 2 3. Insert LP gas tank into the base. 2. Do not touch any of the lantern surfaces as they may be hot 4. Test for leaks 3. Before setting the lantern down, make sure the tank is properly in the base. While Lantern is OFF Checking for Leaks 1. The LP gas tank must be removed and stored properly. Burner Connection 2. Once the lantern is cooled, place the lantern and base in a plastic bag and secure the bag 1. Make sure the control valve is securely fastened to with a string. the burner. (Figure 3) DO NOT COMPLETELY SEAL THE PLASTIC BAG. If your unit was assembled for you, visually check the connection between the burner and control Note: The plastic bag will help protect from insects. valve. WARNING: Failure to inspect this connection or follow these instructions Figure 3 Cleaning and Care could cause a fire or an explosion CAUTION: All cleaning and maintenance should be done when lantern which can cause death, serious bodily is cool and with the fuel supply disconnected. injury, or damage to property. CAUTION: DO NOT clean any lantern part in a self cleaning oven. The 2. If the burner pipe does not rest flush to the extreme heat will damage the finish. control valve, please contact 1.800.762.1142 for assistance. CAUTION: Keep lantern clear and free from combusitble materials, Regulator / 1lbs. LP Gas Tank Connection gasolline, and other flammable vapours and liquids. CAUTION: Do NOT obstruct the flow of combustion and ventilation air. 1. Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water. 2. Make sure control knob is “OFF”. (Figure 1) Notices 3. Spoon several drops of solution, or use squirt bottle, 1. Abrasive cleaners will damage this product. at the LP gas tank to regulator connection. 2. Never use oven cleaner to clean any part of lantern. Figure 4 (Figure 3) Match 3. Do not clean any lantern part in a self cleaning oven. The extreme heat will damage 4. Inspect the solution at the connection, looking for the finish. bubbles. If NO bubbles appear, the connections are secure. Inspecting If bubbles appear, you have a leak. This lantern should be inspected on a regular basis to ensure product safety and longer a. Loosen and retighten this connection, product life. making sure the connection is secure. WARNING: Do NOT attempt to clean this lantern unless the flames are COMPLETELY b. Retest with solution. out and unit is cool to the touch. (About 45 minutes). If you continue to see bubbles after several attempts, disconnect propane 1. Check burner to make sure it is secure. source and contact 1.800.762.1142 2. Check venturi to make sure it is clear and free of spider nests. for assistance. 3. Check all gas connections for leaks. 4. Check components for any signs of damage or rust. Lighting 5. If damage to any component is detected, do NOT operate until repairs are executed. DO NOT expose the lantern to flammable vapors or liquids during lighting. Cleaning Surfaces 1. Make sure all labels, packaging and protective films have been removed from the lantern. WARNING: Do NOT attempt to clean this lantern unless the flames are COMPLETELY 2. Make sure there are no obstructions of airflow to the gas unit. Spiders and insects can nest out and unit is cool to the touch. (About 45 minutes). within and clog the burn...