Votes - 3, Average rating: 4.3 ( )

Manafacture: NuTone File size: 818.81 kb File name: A99044191.pdf Language of manual:

Carefully remove all packing material. Place shelves and hardware package aside until needed. 2. Deteremine desired location of cabinet on wall. Mark wall to show wall opening size (see dimensions chart). Generally, the recommended height to the center of the cabinet is 64” from the floor. Fig. 1 3. CAUTION: Wall studs, plumbing or electrical lines that interfere must be removed or relocated. Cut wall opening, being careful not to damage the MIRROR CARE • Use only clean warm water and a clean, soft, lint-free cloth. • DO NOT USE cleaners that contain solutions of ammonia, vinegar or chlorine. • DO NOT USE powdered cleaners or steel wool. • Never spray cleaning agent directly on mirror, especially on exposed edges and mirror backing. Apply cleaner to soft cloth and wipe mirror. Dry mirror thoroughly. • Keep mirror dry. A well ventilated bathroom is important. 1 2 3 4 5 6 7 Door Pull Placement Mirror Side 1-1/4” 1-1/4” 1-1/8” Left Door Right Door 1-1/8” Back Side Left Door 1 "341 "14Door Bumper Placement Fig. 3Fig. 2 Approx. 64" to Floor WDHFig. 1 surrounding wall surface. Insert framing to support all plaster board edges. 4. Insert cabinet into wall opening in plumb and centered position. Use a carpenter’s level and shim corners of cabinet if necessary. Secure to wall studs through the 4 mounting holes inside cabinet (screws provided). INSTALLATION of SURFACE MOUNT CABINET 1. Position cabinet on wall, making sure it is level. 2. Mark mounting hole locations through back of cabinet and onto wall material. Set cabinet aside. Pre-drill mounting holes if necessary. 3. Re-position cabinet and secure it to wall studs through mounting holes in rear of cabinet. Use four screws (provided). If studs are not available, use 3/16” molly bolts or 3/16” wall anchors, depending on wall material. DOOR PULL AND BUMPER PLACEMENT 1. Clean mirror side of doors thoroughly to prepare surface for self adhesive door pulls. 2. Remove paper backing from door pulls and press them on to mirror side of door at location shown. Fig. 2 3. Clean back side of mirror to prepare surface for self adhesive bumper. Remove paper backing from door bumper and press bumper on to back side of left door. Fig. 3 ASSEMBLE DOORS TO CABINET 1. Insert the TOP of RIGHT MIRROR DOOR into the UPPER REAR TRACK, then move mirror door toward cabinet and lower into the BOTTOM of REAR TRACK. 2. The same procedure is repeated for LEFT HAND MIRROR DOOR except install the door in FRONT TRACK. SERVICE PARTS KEY PART NUMBER NO. DESCRIPTION B703850 B704850 1 2 3 4 5 6 7 Mirror Handle Shelf Bracket - Left Shelf Bracket - Right Shelf Track Bumpon * A99050348 A97017873 3333L 3333R A98010537 A98010546 99100485 Mounting Screw, #8x11/2” A99050344A97017873---- -- A98010565 99100485 Mounting Screw, #8x11/2” *Standard hardware - may be purchased locally. Order replacement parts by “PART NO.” - Not by “KEY NO.” One Year Limited Warranty WARRANTY OWNER: Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recom...

Download now

Please, enter two numbers from picture: