Votes - 3, Average rating: 4
(
)
)
|
manual abstract
• Use for its intended purpose only. The manufacturer is not responsible for any injury or damage resulting from incorrect use or handling (see also Guarantee Terms). • Use only accompanying accessories or those recommended by the manufacturer. • Do not submerge appliance in water or any other liquid. • The cord must not be twisted or wound around the apparatus. • Check regularly that neither the cord nor plug is damaged and do not use if there is any damage, or if it has been dropped on the floor, dropped in water or damaged in any other way. • If the appliance has been damaged, it should be inspected and if necessary repaired by an authorised repair engineer. Never try to repair the appliance yourself. Please contact the store where you bought the appliance for repairs under guarantee. Unauthorised repairs or modifications to the appliance will invalidate the guarantee. KEY TO MAIN COMPONENTS OF THE APPLIANCE 1. Light 2. Swivel joint 3. Battery unit 4. On/Off button (at the reverse side) 5. Motion sensor 6. The button DARKNESS (adjustment of light level) 7. The button TIME (time adjuster) 8. The button SENSITIVITY (sensitivity adjuster) 9. Plug for solar cell panel 10. Solar cell panel 11. Swivel joint 12. Base 13. Screw holes 14. Cord with plug (not shown) Screws and rawlplugs are also included. GENERAL INFORMATION ABOUT SOLAR CELL PANELS • Solar cell panels absorb the sunrays and convert solar energy into electricity that can be stored in rechargeable batteries to provide power for e.g. lights. Solar energy is very environmentally friendly, and the batteries can be recharged over and over again. • For best performance, place solar cell panels out of the shade in a position where they are exposed to direct sunlight in the course of the day. Pay attention to this when choosing where to mount the panel. • Do not cover the solar cell panels and keep them clean so that the sunrays are not obstructed. 1 • Charging capacity of the battery unit depends on the amount of sunlight and is thus depending on geographical position and weather. Obviously, in Northern Europe the solar cells do not have the same effect as in countries with more sunshine hours, which may affect the effectiveness of the light. If the weather is severely cloudy or on short winter days, recharging may sometimes be insufficient for normal use of the light. INSTALLATION Before installation, keep the following in mind: • The solar cell panel (10) and the battery unit (3) with the light (1) are not to be placed so that the cord (14) cannot reach from the solar cell panel to the light. Measure out the distance between the mounting positions before drilling any holes. • Make sure, the cord is not trapped in doors, windows or similar. • Secure the cord with cord fasteners. • The motion sensor (5) is equipped with buttons for both light level (6), time (7) and sensitivity (8). Make sure, it is mounted and adjusted so that is not unnecessarily activated. • The motion sensor must not be mounted where it can be affected by artificial light since this will prevent the light from switching on automatically. Mounting of solar cell panel • The solar cell panel can stand on the triangular base (12) or be mounted on a wall by means of the screw holes (13). Mounting of light and sensor units • Drill two holes in the wall in a vertical line 136 mm apart. • Screw two screws almost all the way in. • Attach the light to the screw heads and make sure it is securely fastened. However, it must be possible to remove the light when turning the appliance on or off. PREPARING THE APPLIANCE • Attach the cord from the solar cell panel to the socket on the battery unit (9). • Adjust the solar cell panel by turning it in the swivel joint (11) in order that it may absorb as much sunlight as possible. • Adjust the light and the motion sensor by turning them in the swivel joints (2) until each points to the direction required. The swivel joints can be tightened using the small finger screw once every part has been correctly adjusted. • Turn the on/off button (4) at the reverse side of the battery unit to the position "Auto". • Return the battery unit with the light to its proper position. • Leave the batteries to fully charge for two days before using. USING THE APPLIANCE • Turn the on/off button to the “AUTO” position (on). • The light now switches on when it is dark and the motion sensor registers movement. • The light switches off in sunlight and is automatically recharged. Use the button “DARKNESS” (light level adjuster) to adjust how dark it should be, before the appliance switches on. • The motion sensor registers movements within a distance of min. 5 m. Use the button “SENSITIVITY” (sensitivity adjuster) to adjust the sensitivity. • Use the button “TIME” (timer) to adjust the interval, the light is to be switched on, every time it is activated. The time can be set for between approx. 3 seconds and approx. 1 minute. • If the light does not switch on, possible causes are...