Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
l Close supervision is necessary when any can opener is used by or near children: l Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning. l Avoid contacting moving parts. l Do not operate can opener with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return can opener to the authorized Sunbeam Appliance Service Station for examination, repair or electrical or mechanical adjustment. l The use of attachments not recommended or sold by the manufacturer may cause fire, electrical shock or injury. l Do not use outdoors. l Do not let cord hang over edge of table or counter or touch hot surfaces. l Do not open pressurized [aerosol-type] cans. l Do not open cans of flammable liquids such as lighter fluids. l Do not use can opener for other than intended use or leave unattended while in use. l Do not operate this appliance in the presence of explosive and/or flammable fumes. SAVETHESEINSTRUCTIONS Read the following instructions before using the unit for the first time. FORHOUSEHOLDUSEONLY This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. Plug electrical cord into 120 volt, 60 cycle AC outlet. Raise can opener lever to upright position (A). Insert can so that the lower edge of the can lip rests on top of the drive wheel. Be certain that the cutting edge is on the inside of the can lip as shown (B).Push can opener lever down firmly (C) and hold until the can lid is automatically pierced and the cutting action begins. It is not necessary to hold the can opener lever down during the cutting cycle. When the can is fully open, the cutting action will automatically stop. The can will remain in position until the lever is raised. To release the can, grasp the can firmly in one hand and raise the lever with the other hand. The magnetic lid holder will retain the lid (D). Dented Cans: Occasionally, badly dented cans will cause the can opener to stall. If this happens, grasp the dented can and guide it through the cutting action manually until the damaged areas are passed. Jammed Cans: To open a can that has become jammed, raise the can opener lever and release the can. Begin the cutting action again in a new place on the can lip. C To insure proper sanitation, all removable parts on the can opener should be detached and cleaned thoroughly in warm, sudsy water at regular intervals. Before cleaning, UNPLUG THE CORD FROM OUTLET. The motor housing easily wipes clean using a damp cloth. Never immerse the motor housing in water. Removing the Lid litter: Lift up to slide out as pictured (E). Removing the Cutting Unit: Raise can opener lever to its fullest upright position. Push can opener lever to the right to remove it from the recessed area (F). Drive Wheel Wipe off drive wheel with a damp cloth. To thoroughly clean drive wheel, use small brush to remove accumulated dirt (G). Replacing the Cutting Unit With can opener lever in raised position, place knob in recessed area. Push lever to the left to snap it into position (H). Replace the lid lifter Twist the knob to raise and lower the cutting assembly. To adjust the height of the cutting assembly follow these directions: 1. Twist the knob in a counter-clockwise direction until the knob clicks into place. The cutting assembly Is raised for opening extra tall cans. 2. Twist the knob in a clockwise direction to lower the cutting assembly for opening regular size cans and for compact storage. The motor and internal gears of your can opener unit are permanently lubricated at the factory for lifetime service and require no further attention. The cutting blade is made of hardened steel and is a special design. It will last for years under normal use. Do not attempt to sharpen. 2 YEAR LIMITED WARRANTY Sunbeam-Oster Household Products warrants that, for a period of two years from date of purchase, this product shall be free of mechanical and electrical defects in material and workmanship. Our obligation hereunder is limited to repair or replacement, at our option, of this product during the warranty period, provided the product is sent postage prepaid directly to our factory service center: SUNBEAM-OSTERHOUSEHOLDPRODUCTS APPLIANCE SERVICE STATION 117 Industrial Central Row Purvis, Ms 39475 Hattiesburg, MS 39401 DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE: THIS MAY DELAY THE PROCESSING OF YOUR WARRANTY CLAIM. This warranty does not cover normal wear of parts, damage resulting from any of the following: negligent use of the product, use with improper voltage or current, use contrary to operating instructions, or disassembly, repair, or alteration by any person other than our factory service center. Pro...