Votes - 1, Average rating: 5
(
)
)
|
manual abstract
3. Place the kettle firmly onto the power base. Plug the power cord into 230/240V power outlet and switch ‘ON’. 4. Press the ON/OFF switch to the ‘ON’ position. The power ‘ON’ light will illuminate. NOTE: Never operate the kettle dry - too little water will result in the kettle switching “OFF”. Do not overfill the kettle - filling above the maximum mark on the water window may result in boiling water splashing from the kettle. NOTE: This kettle must only be used with the power base supplied. Use caution when pouring water from your kettle, as boiling water will scald. Do not pour the water too quickly. NOTE: Do not remove the kettle from the power base during operation. Ensure the kettle has switched to ‘OFF’ position after the water has boiled before removing the kettle from the power base. 5. The kettle will automatically switch ‘OFF’ once the water has boiled. Lift the kettle from the power base and pour the water. Take care to hold the kettle level, especially when filled to the maximum level. To re-boil it may be necessary to wait for a few seconds to allow the control to reset. The kettle should be stored on its power base when not in use. The power outlet should be switched off and the power cord unplugged from the power outlet when not in use. . Caution: this applianCe is designed for the boiling of drinking quality water only, never use it to heat or boil any other liquids or foodstuffs. the lid should always be firmly in plaCe and loCked Closed before use. . Caution: do not release the lid while the water is boiling. ensure the lid is Closed whilst boiling. SAFETY BOIL DRY PROTECTION The kettle is fitted with a safety device, which protects against overheating should the appliance be operated with insufficient water. If this occurs the kettle will stop heating and automatically switch off. Should this occur, switch off at the power outlet and unplug. Allow kettle to cool before refilling. When the kettle has cooled down, the safety device can be reset by removing and then replacing the kettle on its base. KSK210_KETTLE_IB_FA.indd 5 20/5/09 1:50:16 PM CARE AND CLEANING Always switch off at the power outlet, and then unplug the appliance from the power outlet before cleaning. CLEANING THE KETTLE ExTERIOR The outside stainless steel surface of the kettle may be wiped over with a damp cloth and polished with a soft, clean dry cloth. Note: Do not use chemical, steel wool, or abrasive cleaners to clean the inside or outside of the kettle. . Caution: to prevent damage to the applianCe do not use alkaline Cleaning agents when Cleaning, use a soft Cloth and mild detergents. . warning: never immerse the kettle base, switCh area, power base or power supply Cord in water, or allow moisture to Come in ContaCt with these parts. CLEANING THE REMOvABLE FILTER The Kambrook Stainless Steel 1.7L Kettle features a removable mesh filter to filter out scale deposits for cleaner water. To remove the scale deposits, remove the filter by opening the lid of the kettle. Pull the filter firmly to remove. The filter can be cleaned by running under hot water and rubbing with a soft cleaning cloth or brush. To replace the filter, simply press the filter down firmly into the slot behind the spout of the kettle. TIP: The filter could become damaged with time, please check regularly and replace if found damaged. Note: Ensure the kettle and water have cooled down before attempting to clean the filter. MINERAL DEPOSITS AND DISCOLOURATION Due to the large surface area of the concealed element interior base, discolouration due to mineral deposits from tap water may appear more obvious by leaving a brown stain on the base. THIS IS NOT RUST. To remove the discolouration, follow the instructions “Removing mineral deposits”. REMOvING MINERAL DEPOSITS Mineral deposits in tap water may cause the kettle interior and water window to discolour over time. This may be removed by using a proprietary kettle descaler which is available from most leading supermarkets, department stores and hardware stores. ALTERNATIvELY: 1. Fill the kettle until 2.3 full with 1 part vinegar (or a few slices of lemon) and 2 parts water, bring to the boil and allow to stand overnight. 2. Empty the solution from the kettle. Fill the kettle with clean water, bring to boil and discard the water. Repeat and the kettle will be ready for use. STORAGE Ensure the kettle is switched off, cleaned and dried before storing. Ensure that the lid is closed and locked firmly into place. Wrap the power cord around the cord storage under the power base. Stand the kettle upright on the power base. Do not store anything on top. KSK210_KETTLE_IB_FA.indd 6 20/5/09 1:50:16 PM NOTES KSK210_KETTLE_IB_FA.indd 7 20/5/09 1:50:17 PM KAMBROOK 12 MONTH REPLACEMENT WARRANTY Kambrook warrants the purchaser against defects in workmanship and material for a period of 12 months from the date of purchase (3 months commercial use). Guarantee and purchase receipt for this product are to be retained as proo...