Votes - 1, Average rating: 4 ( )

Manafacture: Hoshizaki File size: 1.06 mb File name: Language of manual:

3). Handle the icemaker carefully not to damage the exterior. 4. ELECTRICAL CONNECTIONS WARNING THIS APPLIANCE MUST BE GROUNDED. This icemaker requires a ground that meets the national and local electrical code requirements. To prevent possible severe electrical shock injury to individuals or extensive damage to equipment, install a proper ground wire to this icemaker. Remove the plug from the mains socket before any maintenance, repairs or cleaning is undertaken. * This icemaker must be plugged into the separated power receptacle which has enough capacity. The maximum allowable voltage variation should not exceed ± 10 percent of the nameplate rating. See the Nameplate. * Usually an electrical permit and services of a licensed electrician are required. Max. 0.4” (1 cm) Fig. 2 Fig. 3 Tapped Hole (Leg Mounting) Base Adjustable Leg 5. WATER SUPPLY AND DRAIN CONNECTIONS WARNING To prevent damage to the freezer mechanism, do not operate this icemaker when the water supply is OFF, or if the pressure is below 10 PSIG (0.7 bar), the recommended water pressure. Stop the icemaker until proper water pressure is resumed. CAUTION 1. A brass fitting for the water supply line connection is attached to the 3/4” BSP plastic threads to avoid cross-threading of the Water Valve possibly resulting in leaks. The brass fitting allows connection of a 1/2” FPT that should be connected to the potable water supply line. 2. While making the water supply line connection, use a wrench to hold the brass fitting still to prevent overtightening and damage to the plastic threads. * Water supply inlet for the icemaker is 1/2” female pipe thread (FPT). Note: On water-cooled model, two water supply inlets are provided. One is for the icemaker (1/2” FPT), and the other is for the water-cooled condenser (1/2” FPT). * The brass fitting is attached as shown in Fig. 4. The fitting size is a 1/2” FPT and must be connected only to a potable water supply. * A water supply line shut-off valve and drain valve must be installed. * Water supply pressure should be a minimum of 10 PSIG (0.7 bar) and a maximum of 113 PSIG (7.5 bar). If the pressure exceeds 113 PSIG (7.5 bar), use a pressure reducing valve. * Drain outlet for icemaker dump is 3/4” FPT. Note: On water-cooled model, a 3/8” FPT is provided for the condenser drain outlet. The icemaker drain and the condenser drain piping connections must be made separately. * Drain must be 1/4” fall per foot (2 cm fall per meter) on horizontal runs to get good flow. * Keep a more than 2 vertical inch (5 vertical cm) air gap between the drain pipe end and the sink. * The drain pipe must be so laid as to prevent a backflow into the Storage Bin. Provide a trap in the bin drain line to prevent odor from flowing back into the Storage Bin. 7 8 Fig. 4 Icemaker Shut-off Valve Drain Valve Water Supply Inlet 3/4” BSP Threads Bin Drain Outlet 3/4” FPT 1/4” fall per foot To approved floor drain Brass fitting is attached to Water Supply Inlet. Fitting size is a 1/2” FPT. * A plumbing permit and services of a licensed plumber may be required in some areas. * This icemaker should be installed in accordance with applicable national, state and local regulations. AM-100BAE AM-150BAF Icemaker Shut-off Valve Drain Valve Water Supply Inlet 3/4” BSP Threads Bin Drain Outlet 3/4” FPT 1/4” fall per foot To approved floor drain Brass fitting is attached to Water Supply Inlet. Fitting size is a 1/2” FPT. AM-150BWF Shut-off Valve Drain Valve Condenser Outlet 3/8” FPT Water-cooled Condenser Inlet 1/2” FPT Trap Trap 6. FINAL CHECK LIST 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within 50°F (10°C) to 100°F (38°C) and the water temperature within 41°F (5°C) to 90°F (32°C) all year around? 3) Have all shipping tape(s), string and packing been removed from the icemaker? 4) Are all components, fasteners and thumbscrews securely in place? 5) Have all electrical and piping connections been made? 6) Has the power supply voltage been tested or checked against the nameplate rating? Has a proper earth been installed to the icemaker? 7) Are the Water Supply Line Shut-off Valve and Drain Valve installed? Has the water supply pressure been checked to ensure a minimum of 10 PSIG (0.7 bar) and a maximum of 113 PSIG (7.5 bar)? 8) Have the Compressor hold-down bolts and all refrigerant lines been checked against vibration and possible failure? 9) Has the Bin Control Thermostat been checked for correct operation? When the icemaker is running, cool the Detector of the Bin Control Thermostat. The icemaker should stop within 10 seconds. 10) Has the user been given the Instruction Manual and instructed on how to operate the icemaker and the importance of periodic maintenance recommended? 11) Has the user been given the name and telephone number of the Authorized Service Agency? 7. START UP * Check that shipping tape(s), string and packing are removed before starting the icemaker. 1) Clean inside the Storage Bin and Door...

Download now

Please, enter two numbers from picture: