Votes - 3, Average rating: 4.7 ( )

Manafacture: Follett File size: 4.73 mb File name: Language of manual:

Remove screw at top of louvered panel on left side of unit. 2. Slide panel toward back of dispenser and lift. 3. Remove the air filter located under the louver. 4. Clean with soap and water. 5. Rinse, and replace when completely dry. Semi-annual icemaker cleaning & sanitizing Note: If icemaker and dispenser are cleaned and sanitized at the same time, icemaker should be cleaned and sanitized first. Cleaning solution Solution A: Ice machine cleaner: Prepare one gallon (3.8L) of Follett SafeCLEAN™ Ice Machine cleaner (one 7 oz packet) or equivalent. Solution temperature must be at least 120 F (49 C). Warning: Most ice machine cleaners contain citric or phosphoric acid that can cause skin irritation. Read caution label on product and follow instructions carefully. Sanitizing solution Solution B: Prepare sanitizing solution (50 ppm of available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be 75 F – 125 F (24 C – 52 C). Note: Before cleaning SensorSAFE units, deactivate dispenser by depressing and releasing clean switch located on left side of unit under top front cover. When cleaning is complete, reactivate by depressing and releasing clean switch a second time. Dispenser will automatically reactivate after two minutes. 1. Remove the upper front cover. 2. Remove splash panel and lower drain pan protector. 3. Turn compressor switch on electrical box of icemaker to OFF position. 4. Remove water reservoir cover and close water supply valve. 5. Drain water from reservoir by releasing evaporator drain line from float reservoir bracket and removing plug from drain line. 6. Following manufacturer’s instructions, prepare one gallon (3.8L) cleaning solution A or equivalent. Solution temperature must be at least 120 F (49 C). WARNING: Most ice machine cleaners contain citric or phosphoric acid that can cause skin irritation. Read caution label on product and follow instructions carefully. 7. Plug drain hose, replace drain line in reservoir bracket and pour part of cleaning solution into reservoir, filling it almost to overflowing. 8. Remove stainless steel compression nozzle and drain lines and submerge in a cup of cleaning solution while cleaning rest of system. CAUTION: To avoid potential pitting, do not soak parts in SafeCLEAN for more than 45 minutes. 9. Restore power to icemaker (gearmotor will run; compressor and fan will not). 10. After 15 minutes, turn power OFF; drain solution from reservoir and evaporator. 11. Fill reservoir almost to overflowing with clean, 120 F (49 C) water, and drain. Repeat three times. 12. Following manufacturer’s instructions, prepare 1 gallon (3.8L) sanitizing solution B. Solution temperature must be at least 120 F (49 C). 13. Rinse compression nozzle in clean water and submerge in a cup of sanitizing solution while following steps 14-19. 14. Connect ice transport tube directly onto evaporator outlet port without compression nozzle. Note: If bin will not be cleaned at this time, place a large pan in bin storage area to catch ice or connect a separate ice transport tube to evaporator and divert ice into separate container. 15. Fill reservoir almost to overflowing with sanitizing solution. 16. Restore power to icemaker (gearmotor will run; compressor and fan will not). 17. After 10 minutes, turn compressor switch to ON position. 18. As unit starts to make ice, continue to pour sanitizing solution into reservoir, maintaining level just below reservoir overflow. 19. Continue to make ice with sanitizing solution for 20 minutes. 25CI400A/W • 25HI400A • 50CI400A/W • 50HI400A 20. Turn power to icemaker OFF. 21. Disconnect transport tube from evaporator outlet port. Rinse compression nozzle in clean water and reinstall on evaporator outlet. Reconnect transport tube to compression nozzle. 22. Drain any remaining sanitizing solution from evaporator. 23. Fill reservoir almost to overflowing with clean, 120 F (49 C) water, and drain. Repeat three times. 24. Open water supply valve and replace reservoir cover. Restore power to icemaker and ensure compressor switch is in ON position. Make ice for at least 15 minutes to flush any remaining solution from system. Discard this and all ice made during sanitizing. 25. Inspect evaporator drain pan and drain line and remove any accumulated scale build up. 26. Replace any panels removed prior to cleaning. Start-up following cleaning 1. Clean and sanitize ice storage area of dispenser in accordance with instructions before making ice. 2. Turn icemaker on and begin to make ice. Icemaker should start immediately with power and bin signal supplied. 3. After approximately 30 minutes, test dispenser for proper dispensing. 25CI400A/W • 25HI400A • 50CI400A/W • 50HI400A Dispenser cleaning & sanitizing Periodic cleaning of Follett’s ice and water dispenser system is required to ensure peak performance and delivery of clean, sanitary ice. The following cleaning procedures should be performed at least as frequent...

Download now

Please, enter two numbers from picture: