Votes - 3, Average rating: 4 ( )

Manafacture: Alto-Shaam File size: 1.68 mb File name: Language of manual:

An identification tag is permanently mounted on the appliance. 2. This appliance is equipped with a three-prong grounding plug. For your protection against shock hazard this appliance should be plugged directly into a properly grounded three- prong receptacle. Do not cut or remove the grounding prong from this plug. Plug the unit into a properly grounded receptacle ONLY, positioning the unit so that the plug is easily accessible in case of an emergency. Arcing will occur when connecting or disconnecting the unit unless all controls are in the “OFF” position. 3. Proper receptacle or outlet configuration or permanent wiring for this unit must be installed by a licensed electrician in accordance with applicable local electrical codes. Hot Food Drop-In Well Operation & Care Manual • 4 INSTALLATION ELECTRICAL SPECIFICATIONS Refer to wire diagram sent with unit. ELECTRICAL • 100-HW voltage phase cycle/hz amps kW PLUG CONFIGURATION 120 (agcy) 1 60 4.8 0.6 nema 5-15p 15a-125v plug ELECTRICAL • 200-HW voltage phase cycle/hz amps kW PLUG CONFIGURATION 120 (agcy) 1 60 10.6 1.3 nema 5-15p 15a-125v plug 240 (agcy) 1 60 5.3 1.3 at 208 1 60 4.6 1.0 nema 6-15p 15a-250v plug at 240 1 60 5.3 1.3 230 (agcy) 1 50/60 5.1 1.2 cee 7/7 220-230V plug ELECTRICAL • 300-HW voltage phase cycle/hz amps kW PLUG CONFIGURATION 120 (agcy) 1 60 21.4 2.6 nema l5-30p 30a-125v plug 240 (agcy) 1 60 10.7 2.6 at 208 1 60 9.2 1.9 nema 6-15p 15a-250v plug at 240 1 60 10.7 2.6 230 (agcy) 1 50/60 10.3 2.4 cee 7/7 220-230V plug ELECTRICAL • 400-HW voltage phase cycle/hz amps kW PLUG CONFIGURATION 120 (agcy) 1 60 19.7 2.4 nema l5-30p 30a-125v plug 240 (agcy) 1 60 9.9 2.4 at 208 1 60 8.5 1.8 nema 6-15p 15a-250v plug at 240 1 60 9.8 2.4 230 (agcy) 1 50/60 9.5 2.2 cee 7/7 220-230V plug ELECTRICAL • 500-HW voltage phase cycle/hz amps kW PLUG CONFIGURATION 120 1 60 23.6 2.8 nema l5-30p 30a-125v plug 240 (agcy) 1 60 11.8 2.8 at 208 1 60 10.2 2.1 nema 6-15p 15a-250v plug at 240 1 60 11.8 2.8 230 1 50/60 11.3 2.6 cee 7/7 220-230V plug Hot Food Drop-In Well Operation & Care Manual • 5 INSTALLATION REMOTE CONTROL HOUSING MOUNTING INSTRUCTIONS 400- & 500-HW 100-, 200- & 300-HW PAN DIVIDERBARS #16019FLEXIBLE WATER- TIGHT TETHERApply a food grade siliconealong the outside edge ofthe hot well support flange. FLEXIBLE WATER- TIGHT TETHERDECOR FACE SCREWS 1. 100-HW, 200-HW or 300-HW: Cut a 5-1/4" x 4-1/2" (133mm x 114mm) opening in the location where the control is to be positioned. 400-HW or 500-HW: Cut a 9-1/8" x 4-1/2" (232mm x 114mm) opening in the location where the control is to be positioned. 2. Thoroughly clean and dry the mounting surface around the control cut-out opening on which the decor face will be applied. NOTE: The control face will not properly adhere to an unclean surface. 3. Remove the knob(s) from the thermostat(s) by pulling knob away from control. Remove the decor face from the unit by removing one screw located to the right of the thermostat. (Two screws for double pod.) See diagram a...

Download now

Please, enter two numbers from picture: