Votes - 1, Average rating: 4
(
)
)
|
manual abstract
14. Check ice hopper for presence of foreign objects prior to use. 15. Blades are extremely sharp. Use with extreme caution. 16. DO NOT place on or near a hot gas or electric burner, or in a heated oven. 17. Longer detachable power supply cords can be used if care is exercised in their use. 18. The marked electrical rating of an extension cord should be at least as great as the electrical rating of the appliance. 19. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit into a polarized outlet only one way. SAVE THESE INSTRUCTIONS! INTRODUCTION Thank you for purchasing the one-of-a-kind SNOW CONE CART™. This vintage looking appliance beautifully resembles the carnival style vendors of the early 1900s. Though it may be designed to look like a nostalgic cart of the past, The SNOW CONE CART™ is in fact a technologically modern snow cone maker, and should be treated as such. The SNOW CONE CART™ uses ice cubes from your freezer or icemaker to create: • Snow Cones • Slushies • Smoothies • Low Fat Snacks The SNOW CONE CART™ is designed for indoor use and can be used in a number of locations such as: • Family Rooms • Dorm Rooms • Offices • Club Houses Now you can enjoy icy, cool snow cones to snack on when…… • Watching TV or a Movie at Home • Throwing a Party • Listening to Music • Craving a Low fat Treat ENGLISH 3 3 ASSEMBLY After Taking the Unit Out of the Box: Your SNOW CONE CART™ requires some assembly before first use. The Main Unit, which includes the ice grinder, is already assembled. You will need to put together the cart itself using the instructions that follow. Before first use, make sure to wipe clean the inside of the Main Unit with a non-abrasive moist sponge, a non-abrasive towel, or a damp cloth followed by a non-abrasive dry towel. BREAKDOWN Parts ENGLISH 4 ASSEMBLY (Continued) Screws, Studs, and Nuts 1 2 3 4 5 6 7 8 ASSEMBLY Main Unit Base Support Storage Compartment 1. Open the box and remove all parts including the Main Unit, Storage Compartment, Wheels, Legs, and all other contents (including the Push Handle and accessories). 2. Attach the Push Handle to the Storage Compartment using four of the #1 screws (as shown below): ENGLISH 5 ASSEMBLY (Continued) 3. Connect the Base Supports by screwing two of the #1 screws into the Cross Bar (as shown below): 4. Connect the Leg Assembly by screwing four of the #3 studs from the Base Support into the Leg Assembly (as shown below). Make sure to screw from the Base Support into the Leg Assembly and not vice versa. Once the studs are firmly screwed through, place the four #8 Nut Caps over the studs for cosmetic purposes: 5. Now that the Leg Assembly and Base Support have been connected, use four of the #2 screws to connect the Storage Compartment to the Base Support (as shown below). Once you have successfully screwed the #2 screws through the Storage Cabinet and into the Base Support, place the Bottom Plate underneath the Storage Cabinet and attach it to the Base Support using four of the #1 screws: ENGLISH 6 ASSEMBLY (Continued) 6. Attach the Wheels to the Base Support by using two of the #4 Wheel Rods. Slide a #5 Lock Washer onto a Wheel Rod, and then push the Wheel Rod through the holes in the Base Support. Make sure to place the two #6 Flat Washers between the Base Support and the Wheels. Repeat on the other wheel. Finally, place the two #7 Wheel Rod Caps on the outside of the screws for cosmetic purposes (as shown below): 7. Place the Main Unit onto the Storage Compartment so that the two side holes match up. Connect the Main Unit to the Storage Compartment using the two included Lock Screws (D) as shown below: 8. Place the Clear Plastic Bowl into the top of the Main Unit and firmly secure the lid into the bowl. Make sure that the end of the lid with the two tabs is properly placed into the corresponding holes and the lid snap shuts. Please note that the ice will not shave unless the lid is properly secured. Never force it down. You are now ready to use your SNOW CONE CART™! Helpful Hint: Use the black plastic adjusters on the bottom of the feet to properly level. ENGLISH 7 USING YOUR SNOW CONE CART™ USING YOUR SNOW CONE CART™ First, find a stable surface near an electrical outlet before starting. (Make sure your cord is away from any water source. If needed, it is acceptable to use an extension cord.) 1. Before plugging in your unit, add ice cubes by removing the clear lid from the Main Unit of your SNOW CONE CART™. In order to do so, simply push the release button on the lid, lift and remove. Once you have done this, plug in the unit. For Optimal Ice Shaving Results – Your ice cubes should sit a short while before putting them in the shaving unit. If your ice has a frosty look, it is much too hard to shave. If your ice sits long enough to look clear and it is wet to the touch, then it is ready to make your SNOW CONE CART™ experience a fun one. 2. When ice cubes a...