• The ice maker will automatically begin approximately 15 seconds after the last button is pressed. Please note: The length of the ice making process is directly proportionate to the current ice size setting and batch completion time range between 9 minutes and 15 minutes per cycle, depending upon your ice size selection. For optimal results, please keep the ice maker door closed during the ice making process. Ice Size Selection 1 Press Power or enter Delayed Start mode (see below). 2 Depress the ice size selection button on the control pad. The ice size selection button allows you to choose from small, medium or large ice cubes. By default your ice maker is configured to produce medium size ice cubes. However if you would like a different size of cube, you need only depress the ice size selection button to cycle between the three (3) available sizes (small, medium and large.) Ice size change is possible during the running ice making cycle, however it is recommended to wait until the current cycle is complete before defining a new ice size. NOTE: Unless there is a power failure or power interruption to the unit. The ice size selection you have made will be retained as the default ice size. Delayed Start 1 Add water to ‘fill line’. 2 Ensure the power is off. 3 Press the increase & decrease arrows simultaneously 4 Select timer length. 5 Select required ice size. • Remove ice bucket and add water to Fill line.(approx. 3.5 L) • With the power off. Press the Increase/Decrease buttons once simultaneously to enter the timer set mode. • Each subsequent press of the increase button will increase the timer in 30 minute increments up to 12 hours. Alternatively to subtract time from the timer, press the decrease button to decrease the timer by 30 minute increments. • Reinsert the ice bucket and select the ice size you require. • The ice maker timer will automatically start 10 seconds after the last button is pressed. To cancel the timer at any time and begin the ice making process immediately, simply press the power button. 7 Operating Instructions Self-Clean Mode 1 Add water & vinegar (1:1) 2 With the power off, simultaneously depress the increase & decrease arrows twice. 3 Drain after program is complete. 4 Add fresh water to fill line. 5 Repeat Step 2 6 Drain after program is complete. The self-clean mode should be put into operation before you use your ice maker for the first time and/or if there has been a long period without use. Stage 1 • Add equal parts of water and vinegar (1:1) to the ice maker’s reservoir. • With the power off, press the increase and decrease arrows simultaneously two times to activate the self-clean mode. Please note, the self clean mode with automatically initiate approximately 10 seconds after the last button depression. • During the self clean mode, the upper ice bucket is filled and dumped multiple times and the pump will remain in continuous operation as it feeds water to the bucket and evaporator coils. This cycle continues for approximately five-anda- half minutes. Upon completion, the unit automatically powers down and is now ready for stage 2. Stage 2 • Drain the cleaning solution from the internal reservoir by removing the rear drain cap and plug (see pg. 9). • Add fresh water to the ‘Fill line’ in the internal reservoir. • With the power off, press the increase and decrease arrows simultaneously two times to activate the self clean mode- which will now act as a rinse. Upon completion of this final stage of the self clean process, the unit automatically powers down once again. Proceed to drain the water from the internal reservoir and leave the lid on the ice maker open to allow it to air dry. 8 Instrucciones de Operacion Funciones de su Equipo para Fabricar Hielo Exterior 1 Puerta del Equipo para Fabricar Hielo con ventana. 2 Panel de Control (vea pagina 30 por mas detalles) 3 Patas Ajustables. Interior 4 Serpentinas Evaporadoras. 5 Tanque de Agua. 6 Pala para Hielo. 7 Linea de lleno de agua. Accesorios 8 9 6 5 4 1 2 3 7 8 Tapon de Drenaje. 9 Recipiente del Hielo. 29 INSTRUCCIONES IMPORTANTES DE SEGURIDAD INSTRUCCIONES DE LA CONEXION A TIERRA ADVERTENCIA La conexion inadecuada del cable de tierra puede causar riesgo de descarga electrica. Este artefacto debe ser conectado a tierra. En caso de un corto circuito electrico, la conexion a tierra reduce el riesgo de una descarga electrica proporcionando un cable de retorno para la corriente electrica. Este artefacto viene con un cable de alimentacion que tiene un conductor y pata del enchufe de tierra. Este cable debe enchufarse en un tomacorriente debidamente instalado y con conexion a tierra. Si no entiende claramente las instrucciones de conexion a tierra, o si no esta seguro de que su tomacorriente este correctamente conectado a tierra, llame a un electricista calificado. Si el tomacorriente es uno comun de 2 patas, es su responsabilidad personal y obligacion el reemplazarlo por uno de 3 patas correctamente conectado a tierra. Par...