Votes - , Average rating: ( )

User manual Cleveland Range, model (T) MKDL-125-T (-CC)

Manafacture: Cleveland Range
File size: 2.11 mb
File name:

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

May be replaced by tilt switch if unit is power tilt. 4. Steam Valve ............. .Manually controls the amount of steam entering the kettle. 5. Scraper Blades........... .Scrapes the side of the kettle and moves product away 6. Main Agitator Arm......... .Provides most of the product movement. 7. Temperature Probe ........ .Probe holds temperature sensors for controller. 8. Secondary Arm ........... .Provides reverse agitation and product lift in kettle. 9. Drain Cock .............. .Used to manually drain condensate from kettle. 10. Product Discharge Valve . . . .Discharge valve for product in the kettle. 11. Mixer Bridge ............. .Encloses agitator motors. 12. Secondary Speed Control . . .Controls speed of secondary agitator arm. 13. Faucet Spout ............. .Delivers water to the kettle. 14. Hot Water Valve........... .Turns on hot water 15. Cold Water Valve.......... .Turns on cold water. 16. Mixer Speed Control....... .Controls speed of agitators and mixer bridge lift mode. 17. Mix/Lift Switch............ .Sets hydraulics to mix or lift mode. 18. Up/Down Switch .......... .When unit is in lift mode, bridge can be raised or lowered with this switch 19. Emergency Stop .......... .Stops hydraulic system. 20. Controller Keypad......... .Used to set temperature parameters. 21. On/Off Switch ............ .Power switch to water meter 22. Start Switch.............. .Starts water flow to kettle. 23. Interrupt Switch........... .Interrupts flow without resetting water meter 24. Active/Bypass Switch ...... .Switch to activate or bypass (manual operation) the controller. 25. Controller Switch.......... .Dual function switch for auto mode or manual heat, cool or off mode. 26. Main Power Switch ........ .Power switch for unit. 27. Water Meter Control ....... Display and setting for water meter Operating Suggestions Cleveland Range Mixer Kettles are simple and safe to operate. The following tips will allow you to maximize the use of your new mixer. 1. To achieve optimum performance on tilting kettles; Before applying steam to a cold kettle, open the DRAIN COCK to drain condensate from the kettles jacket. Close drain cock when unit is fully drained. 2. Allow unit to preheat before addition of product to kettle. However when cooking egg and milk products, the kettle should NOT be preheated, as products of this nature adhere to hot cooking surfaces. These types of foods should be placed in the kettle before heating is begun. 3. An important part of kettle cleaning is to prevent foods from drying on. For this reason, cleaning should be completed immediately after cooked foods are removed. Refer to the "Care and Cleaning" instructions for detailed kettle washing procedures. 4. If a mixer bridge is equipped with a temperature probe for a controller or thermometer, the probe must be submerged a minimum of three inches in the product for accurate readings. Safety 1. Close PRODUCT DISCHARGE VALVE before filling the kettle. 2. When raising or lowering MIXER BRIDGE, insure FAUCET SPOUT is not in the way of MAIN AGITATOR ARM or damage to spout will result. 3. As a safety precaution the MIXER SPEED CONTROL must first be turned to zero before unit will start to mix. 4. Always remember, like a cooking pot the kettles become very hot when cooking. Avoid contact with bare skin. OFF ON OFF UP DOWN General Operation 1. Turn MAIN POWER SWITCH to "ON". Lifting & Lowering Bridge WARNING- Insure FAUCET SPOUT is out of way before raising or lowering bridge. 1. Turn MIX/LIFT SWITCH to "LIFT". 2. Turn MIXER SPEED CONTROL to "MIN" and back up to #5. 3. Turn and hold UP/DOWN SWITCH "UP" to raise or "DOWN" to lower. Mixing 1. Turn MIX/LIFT SWITCH to "MIX". 2. Turn MIXER SPEED CONTROL to "MIN" and slowly adjust to desired speed. 3. Adjust SECONDARY SPEED CONTROL to desired speed. Tilting Kettle 1. Raise MIXER BRIDGE and swing to side. 2. For manual tilt: turn HANDWHEEL. 3. For power tilt: turn switch " K" to raise, or " y to tilt. WARNING- Do not tilt kettle when mixer agitators are in kettle bowl. â Discharge Valve 1. For air valve: turn AIR REGULATOR clockwise to open, or counterclockwise to close. 2. For butterfly valve: push handle in and pull upwards to open. ........... TS-y Adding Water Manually 1. Locate FAUCET SPOUT over desired kettle. 2. Turn on HOT or COLD WATER VALVES. & ppf Manual Heating/ Cooling 1. Turn ACTIVE/BYPASS SWITCH to "BYPASS". 2. Turn CONTROLLER SWITCH to "HEAT" or "COOL". 3. For heat: open STEAM VALVE completely to boil, or adjust to regulate temperature. For cooling: open STEAM VALVE completely. DIGITAL WATER METER OPERATING INSTRUCTIONS Note: The digital counter has been preset at the factory and should operate satisfactory. If installing a new counter (or the configuration settings to your existing digital counter become corrupted) you must configure the digital counter as shown below (Configuring a Digital Counter) prior to operation. ...