Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible. A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251. RETURN TO TOP OF THE PAGE North Europe Information Placering/Ventilation VARNING: FORSAKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG AR LATATKOMLIGA, NAR DU STALLER DIN UTRUSTNING PAPLATS. Placering/Ventilation ADVARSEL: SORG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILG.NGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTA VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NAR DETTE UTSTYRET PLASSERES, MA DU PASSE PA AT KONTAKTENE FOR STOMTILFORSEL ER LETTE A NA. RETURN TO TOP OF THE PAGE BSMI Notice (Taiwan Only) RETURN TO TOP OF THE PAGE Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung uber den Schutz vor Schaden durch Rontgenstrahlen" festgelegten Vorschriften. Auf der Ruckwand des Gerates befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften uber die Bauart von Storstrahlern nach Anlage III ¤ 5 Abs. 4 der Rontgenverordnung erfullt sind. Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, da. 1. Reparaturen nur durch Fachpersonal durchgefuhrt werden. 2. nur original-Ersatzteile verwendet werden. 3. bei Ersatz der Bildrohre nur eine bauartgleiche eingebaut wird. Aus ergonomischen Grunden wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhohte Augenbelastung bei zu geringem Zeichenkontrast waren die Folge). Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betragt 70dB (A) oder weniger. ACHTUNG: BEIM AUFSTELLEN DIESES GERATES DARAUF ACHTEN, DA. NETZSTECKER UND NETZKABELANSCHLU. LEICHT ZUGANGLICH SIND. RETURN TO TOP OF THE PAGE End-of-Life Disposal Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer. RETURN TO TOP OF THE PAGE Information for UK only WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A. S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3- pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere. How to connect a plug The wires in the mains lead are coloured in accordance with the following code: BLUE - "NEUTRAL" ("N") BROWN - "LIVE" ("L") GREEN & YELLOW - "EARTH" ("E") 1. The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter "E" or by the Earth symbol or coloured GREEN or GREEN AND YELLOW. 2. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK. 3. The BROWN wire must be connected to the terminal which marked with the letter "L" or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires. RETURN TO TOP OF THE PAGE Altre Informazioni Precauzioni di sicurezza e manutenzione • Risoluzione dei roblemi • Normative • Informazioni per gli utenti degli Stati Uniti •Informazioni per gli utenti non statunitensi Informazioni per gli utenti degli Stati Uniti Per i monitor predisposti per 115 V: Usate un set di collegamento elettrico certificato UL, consistente di un cavo di alimentazione a tre fili conduttori di tipo SVT o SJT con sezione minima di 18 AWG e lunghezza massima di 457 cm, e di una spina per messa a terra da 15 A, 125 V con laminetta parallela. Per i monitor predisposti per 230 V: Usate...