Login:
Votes - 5, Average rating: 4 ( )

User manual Dimplex, model THE ELECTRIC WALL MOUNTED FIREPLACE EWM-SS

Manafacture: Dimplex
File size: 472.53 kb
File name: 78408e33-1fde-4e2d-bb79-f7f417352ebe.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


7. When installing into one stud, use one of the three center locations as indicated in FIGURE 4. The wall anchors must be installed into the outer most locations as indicated in FIGURE 4. 8. Hold the wall-mounting bracket on the wall and mark the location of ONE of the mounting holes. 9. Install the bubble level onto the top of the wall-mounting bracket. (FIGURE 3 & 4). 10. Adjust the wall-mounting bracket so the bubble on the level is centered between the two black lines. 11. Mark two other mounting screw locations on the wall bracket ensuring that the wall bracket stays level. 12. Drill .” holes into the wall on the marked locations where the wall anchors are to be installed. (FIGURE 1) 13. Insert the wall anchor screws through the wall bracket and thread into the wall anchors. The screws should extend beyond the wall anchors. (FIGURE 2) 14. Squeeze the wall anchor together and insert the wall anchors into the .” holes in the wall. Tighten the screws. (FIGURE 2) 15. Install the remaining screws into the wall studs as required. Note: At least one of the mounting screws must be installed into a wall stud. 3 4 UNIT INSTALLATION CORD SECURING (VIEW FROM BACK) 5 OPERATION The controls are located on the lower right side of the wall mounted electric fireplace. (FIGURE 7) A. MAIN ON/OFF SWITCH The on/off switch supplies power to all unit functions (heat/flame) B. HEATER ON/OFF SWITCH The HEATER ON/OFF SWITCH supplies power to the heater fan and the heater element. C. HEATER THERMOSTAT CONTROL To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the way to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at this setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on. To turn the heater off, switch the HEATER ON/OFF SWITCH to the OFF position. NOTE: When the heater is switched ON, the heater fan will operate. The heater element may or may not be on, depending on the thermostat control setting (SEE “HEATER THERMOSTAT CONTROL”). FIGURE 7 (LOWER RIGHT SIDE) 6 RESETTING THE TEMPERATURE CUTOFF SWITCH Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the MAIN ON/OFF SWITCH to OFF and waiting 5 minutes before switching the unit back on. CAUTION If you need to continuously reset the heater, unplug the unit and call Dimplex customer service at 1-888-DIMPLEX (1-888-346-7539). MAINTENANCE WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. LIGHT BULB REPLACEMENT Allow at least 5 minutes for light bulbs to cool before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. There are two bulbs under the log set which generate the flames and embers. TOOL REQUIREMENTS Slot screw driver HELPFUL HINTS It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace light bulbs. LOWER LIGHT BULB REQUIREMENTS Quantity of 3 – 35 Watt Clear Halogen Lamps, 120 Volt, G9 base. DO NOT EXCEED 35 WATTS PER BULB. LOWER BULB REPLACEMENT 1. Unplug the unit from the outlet. 2. Remove the two mounting screws from the bottom front of the heater assembly. (FIGURE 2) 3. Loosen but do not remove the four heater and light assembly mounting screws located on the bottom sides of the wall mounted electric fireplace. (FIGURE 2) 4. Slide the heater and light assembly forward to release it from the bottom of the wall mounted electric fireplace (FIGURE 1). 5. Place heater and light assembly on a flat surface and examine the bulbs to determine which bulb(s) required replacement 6. Remove the burnt out bulb(s) by gently pulling straight out of socket. If bulbs are difficult to remove from socket move the bulb from side to side while pulling being careful not to damage the light socket. 7. Insert new bulb(s). 8. Install the heater and light assembly onto the four mounting screws. 9. Slide the assembly backwards to lock it into position. 10. Tighten the four heater and light assembly mounting screws. 11. Install the two front mounting screws. 12. Plug in the wall mounted electric fireplace. 7 FIGURE 1 FIGURE 2 GLASS CLEANING The front glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the front glass may collect dust particles, these can be removed by dusting lightly with a clean dry cloth. To remove fingerprints or other marks, the glass can be cleaned with a damp cloth. The glass should be completely dried with a lint free c...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category