Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
H. BRADY CO. AUTOMATIC IDENTIFICATION PRODUCTS Bradyprinte. T. TH. Mode. 200. an. 260. Therma. Transfe. Printe. USER'. GUID. Custome. par. #31450L-1. Manufacture. par. . 31450LB-1. Rev. . W. H. BRAD. CO. AUTOMATI. IDENTIFICATIO. PRODUCT. Proprietary Statement . This manual contains proprietary information of Brady USA, Inc. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Brady USA, Inc. Product Improvement. Continuous improvement of products is a policy of Brady USA, Inc. All specifications and signs are subject to change without notice. FCC Compliance Statemen. Note: This equipment has been tested and found to comply with the limits for a Class A digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. In order to insure compliance, this printer must be used with a Shielded Power Cord and Shielded Communication Cables. “ The user is cautioned that any changes or modifications not expressly approved by Brady USA, Inc. could void the user’s authority to operate the equipment.” Canadian DOC Compliance Statemen. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. Liability Disclaime. Brady USA, Inc. takes steps to assure that its published Engineering specifications and Manuals are correct; however, errors do occur. Brady USA, Inc. has been advised of the possibility of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you. Copyright. The copyrights in this manual and the label printer described therein are licensed to Brady USA, Inc. All rights are reserved. Unauthorized reproduction of this manual or the software in the label printer may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability. ZPL II® and E3® are registered trademarks of Zebra Technologies Corporation Centronicsa is a registered trademark of Genicom Corporation IBMa is a registered trademark of IBM Corporation © Zebra Technologies Corporation, portions © Brady USA, Inc. Bradyprinter™ OO TH. Model. 200. an. 260. WARRANT. INFORMATIO. 1. Printe. Warrant. BRADY printers, excluding thermal printheads which are warranted separately below, are warranted against defects in material or workmanship for six (6) months from the date of original shipment by BRADY USA, INC. This warranty does not cover normal wear and tear and shall be null and void if the equipment is modified, improperly installed or used, damaged by accident or neglect, or in the event any parts are improperly installed or replaced by the user. Since printhead wear is part of normal operations, the original printhead and replacement printheads are covered by a limited warranty of six (6) months from the date of original shipment by BRADY USA, Inc. To qualify for this warranty, the printer must be returned to the factory or other authorized service center. Although the user is not required to purchase BRADY brand supplies (media and/or ribbons), to the extent it is determined that the use of other supplies (media and/or ribbons) shall have caused any defect in the thermal printhead for which a warranty claim is made, the user shall be responsible for BRADY USA, INC.’s customary charges for labor and materials to repair such defect. To the extent that it is determined that failure to follow the preventive maintenance schedule and procedures listed in the User Guide shall have caused any defect in the thermal printhead for which a warranty claim is made, this limited warranty shall be void. BRADY USA, INC.’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE TO FURNISH PARTS AND LABOR FOR THE REPAIR OR REPLACEMENT OF PRODUCTS FOUND TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP DURING THE WARRANTY PERIOD. As a condition of this warranty, the user must: (a) obtain a BRADY Return Authorization for the printer, or subassembly(s); (b) ship the printer or subassembly(s), transportation prepaid to the authorized service location; and (c) include with the Product or subassembly(s) a written description of the claimed defect....
Other models in this manual:Printers - 260M (1.46 mb)