Votes - 2, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
7 Place the print head in the holder. 5 8 Lock the print head into place by lowering the lever. Do not touch the lock lever once the print head has been installed. n Installing the Ink Tanks • For safety reasons, store ink tanks out of the reach of small children. • Do not drop or shake ink tanks. 1 Take out the yellow ink tank. 2 Pull the orange tape in the direction of the arrow and remove the clear film. electrical contacts print head nozzles print head holder print head 3 Hold the ink tank as shown in the diagram and remove the protective cap. aNotes • Do not squeeze the sides of the ink tanks as this may cause the ink to leak out and stain your clothes and hands. • Do not touch the ink port. • Do not attempt to reattach the protective cap once it has been removed. 4 Insert the yellow ink tank into the righthand slot. Press the top until it clicks into place. 6 5 Use the same procedure to install the other ink tanks in their appropriate slots. Check the labels to make sure that each tank is in the correct position. aNotes • Only install the ink tanks in the positions specified by the labels. • If ink tanks are not installed in the right position, colours will not be printed correctly. Immediately reinstall the tank in the correct position and carry out print head cleaning. For details, refer to the User’s Guide. 6 Close the front cover. Wait until the POWER lamp remains fully lit. ink port Black Yellow Magenta Cyan Photo Cyan Photo Magenta nn 4 n Loading Paper nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn n Loading A4 (Letter) Size Plain Paper 1 Open the front cover. 2 Move the paper thickness lever at the top of the print head holder to the left position. Close the front cover. a Note Set the paper thickness lever to the left when using plain paper, to the right when using thick paper. Refer to the User’s Guide for information on loading envelopes and other media. paper thickness lever print side 3 Load the paper, aligning it with the right side of the sheet feeder. You can load up to 100 sheets of plain paper. Do not exceed this limit. After printing, do not stack more than 50 sheets in the paper output tray. 4 Press the paper guide and slide it against the left side of the stack of paper. You now need to install the printer driver: Windows: Go to page 8 Macintosh: Go to page 10 nn 5 n Installing the Printer Driver nnnnnnnnnnnnnnnnnnnnnn n Installing the Printer Driver - Windows a Notes • Do not disconnect the cable or remove the CD-ROM during the installation. The driver cannot be correctly installed. • The screens below refer to Windows Me installation. Screen may differ depending on the environment you are using. • When installing the printer driver in Windows XP, Windows 2000 or Windows NT 4.0, log on to the system as a member of the Administrators group. If the following screen appears automatically, click Cancel and follow steps 1 to 7 to install the printer driver. Special Notes for Windows 98 USB Users Click Cancel to quit the screen and turn off the printer. Next, remove and replace the USB cable connected to your computer. OFF 1 Ensure the printer and computer are switched off. 2 Turn on the computer and start Windows. If any applications automatically run, quit them. Disable any virus detection programs. Do NOT turn the printer on at this stage. 3 Place the Setup Software & User’s Guide CD-ROM in the CD-ROM drive. ON a Notes • If the CD-ROM does not run automatically, double-click My Computer in the Windows screen, for Windows XP, click Start and select My Computer, and then double-click the CD-ROM icon. • If the language selection screen appears, select a language, then click the Next button. 4 Follow the instructions displayed on the screen. When the screen shown on the left is displayed, click Install. 5 When the screen shown on the left appears, turn the printer on. If the printer is recognised, the printer driver will be automatically installed. a Note If the connection is not recognised, refer to the section “Notes on Handling the USB Interface (for Windows Users)” on page 21. 6 Click OK. Before you can use the printer, you must carry out print head alignment on page 12. 7 When the screen shown on the left appears, click Exit. a Note • To view the User's Guide, please refer to page 21. • If a message prompting you to restart the computer appears, click Yes. n Installing the Printer Driver - Macintosh a Notes • Do not remove or insert the USB cable during installation, as this may result in the computer or printer not operating correctly. • Before installing the driver, disable all virus detection programs and automatically loading programs or remove them from your system folder. 1 Turn on the Mac. 2 Place the Setup Software & User’s Guide CD-ROM in the CD-ROM drive. 3 Double-click the printer driver folder, then select a language. 4 Double-click Installer. 5 Read the Licence Agreement and click Accept to continue. 6 Click Install. Wait for the installation to finish. a Note If the above message a...