Votes - 4, Average rating: 4.5
(
)
)
|
Other manuals for this model:
manual abstract
PRINTER DRIVER FEATURES Your printer drivers support the following standard features: • Paper orientation, size, source and media type selection • Number of copies In addition, you can use various special printing features. The following table shows a general overview of features supported by your printer drivers: Printer driver FEATURE WINDOWS LINUX MACINTOSH Color mode O O O Machine quality option O O O Poster printing O X X Multiple pages per sheet (N-up) O O (2, 4) O Fit to page printing O X Oa Scale printing O X O Different source for first page O X O Watermark O X X Overlay O X X Duplex O X O a.This feature is not supported MAC OS X 10.3. PostScript driver FEATURE WINDOWS LINUX MACINTOSH Color mode O O O Machine quality option O O O Poster printing X X X Multiple pages per sheet (N-up) O O (2, 4) O Fit to page printing O X Oa Scale printing O X O Different source for first page X X O Watermark X X X Overlay X X X Duplex O X O a.This feature is not supported MAC OS X 10.3. 24 _Introduction getting started This chapter gives you step-by-step instructions for setting up the machine. This chapter includes: • Setting up the hardware • Printing a demo page • Setting up the network SETTING UP THE HARDWARE This section shows the steps to set up the hardware which is explained in the Quick Install Guide. Make sure you read Quick Install Guide and complete following steps. 1. Select a stable location. Select a level, stable place with adequate space for air circulation. Allow extra space to open covers and trays. The area should be well-ventilated and away from direct sunlight or sources of heat, cold, and humidity. Do not set the machine close to the edge of your desk or table. Printing is suitable for altitudes under 1,000 m (3,281 ft). Refer to the altitude setting to optimize your printing. See "Altitude adjustment" on page 28 for more information. Place the machine on a flat, stable surface so that there is no incline greater than 2 mm (0.08 inch). Otherwise, printing quality may be affected. • System requirements • Installing the software • Machine's basic settings 2. Unpack the machine and check all the enclosed items. 3. Remove the tape holding the machine tightly. 4. Install the toner cartridge. 5. Load paper. (See "Loading paper" on page 36.) 6. Make sure that all the cables are connected to the machine. 7. Turn the machine on. When you move the machine, do not tilt or turn it upside down. Otherwise, the inside of the machine may be contaminated by toner, which can cause damage to the machine or bad print quality. PRINTING A DEMO PAGE Print a demo page to make sure that the machine is operating correctly. To print a demo page: In ready mode, press and hold the OK button for about 2 seconds. SETTING UP THE NETWORK You need to set up the network protocols on the machine to use it as your network printer. You can set up the basic network settings through the machine's control panel. Supported operating environments The following table shows the network environments supported by the machine: ITEM REQUIREMENTS Network interface • Ethernet 10/100 Base-TX • IEEE 802.11 b/g Wireless LAN (optional) Network operating system • Windows 2000/XP/2003/Vista • Various Linux OS • Mac OS X 10.3 ~ 10.5 Network protocols • TCP/IP on Windows • IPP • SNMP • DHCP • BOOTP If you want to set up DHCP network protocol, go to developer.apple.com/networking/bonjour/download/, select the Bonjour program that is appropriate for your computer operating system and install the program. This program will allow you to set network parameters automatically. Follow the instructions in the installation window. This program does not support Linux. Getting started_25 Configuring network protocol via the machine You can set up TCP/IP network parameters, follow the steps listed below. 1. Make sure your machine is connected to the network with an RJ-45 Ethernet cable. 2. Make sure you have turned on the machine. 3. Press Menu() on the control panel, until you see Network on the bottom line of the display. 4. Press OK to access the menu. 5. Press the left/right arrow until TCP/IP displays. 6. Press OK. 7. Press the left/right arrow until Static displays. 8. Press OK. 9. Press the left/right arrow until IP Address displays. 10. Press OK. Enter a byte between 0 and 255 using the number keypad and press the left/right arrow to move between bytes. Repeat this to complete the address from the 1st byte to the 4th byte. 11. When you have finished, press OK. Repeat steps 9 and 10 to configure the other TCP/IP parameters: subnet mask and gateway address. Contact the network administrator if you are not sure how to configure. You can also set up the network settings through the network administration programs. • SyncThru™ Web Admin Service: Web-based printer management solution for network administrators. SyncThru™ Web Admin Service provides you with an efficient way of managing network devices and lets you remotely monitor and troubleshoot network...
Other models in this manual:Printers - CLX-6200ND (9.49 mb)
Printers - CLX-6210FX (9.49 mb)
Printers - CLX-6200FX (9.49 mb)
Printers - CLX-6210FXK (9.49 mb)