All Rights Reserved. 1 Introduction Warning To ensure your personal safety, read “Safety Information” (below) before you use the controller. The AirAlertTM96d system sets new standards in gas detection and in the measurement of environmental parameters. Acting as the nerve center of a modular gas detection network, the AirAlertTM96d provides continuous monitoring of up to 96 connected units on three distinct channels. The AirAlertTM96d provides a full array of displays. At a glance, it is possib

• When installed properly, can supervise the pilot flame and/or the main burner flame. w Mounts easily on a standard 314 inch sight pipe. • The lead sulfide photocell plugs into an electrical socket in the C?OlSA assembly and is field replaceable. • The lead sulfide photocell’s sensitivity to infrared radiation is compatible with a wide range of flame supervisory applications. W Models are available with leadwire lengths of 30, 48 and 96 inches [0.76, 1.22,2.64 m]. W Flexible metal cable protect

Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after Software Changes: To ensure proper system operation, this product must be tested in accordance with NFPA 72 after any programming operation or change in site-s

This warranty extends only to the sale of new and unused products to the original buyer. BWs warranty obligation is limited, at BWs option, to refund of the purchase price, repair or replacement of a defective product that is returned to a BW authorized service center within the warranty period. In no event shall BWs liability hereunder exceed the purchase price actually paid by the buyer for the Product. This warranty does not include: a) fuses, disposable batteries or the routine replacement

Contact authorized service personnel immediately. See below. Manual activation (Fire Drill or otherwise) Notification Appliance Circuits (NACs) can be activated by pressing and holding the DRILL button for at least two seconds. NOTE: You may want to disconnect the municipal box by sliding the DISCONNECT switch, located on the 4XTMF module, to its disconnect position (to the right). If a DACT is connected, notify the monitoring service before conducting any fire drills or tests. Alarm Silenc

LCD display will read SYSTEM following location: ALL NORMAL. WHEN AUDIBLE DEVICES ARE SOUNDING -FORANALARM 1. Evacuate the protected area 2. Notify the monitoring service and/or the Fire Department immediately. Tell them briefly what happened and what your current status is. Phones:__ Fire Department Monitoring Service 3. If the Fire Department is responding, be prepared to provide directions to arriving firefighters. FOR TROUBLE, SUPERVISORY, AND EMERGENCY ALARMS 1. Notify the monitori

The "ISOLATE" button will need to be depressed again to re-enter isolate mode. If a correct entry is made, the zone is immediately isolated. If the zone is already in alarm, all of its alarm outputs are isolated and indicators remain visible. If the "ALL" function is performed, all zones will be isolated, regardless of their previous state. Performing the "ALL" function for a second time will de-isolate all zones. RESET RESET # ENTER The reset function momentarily disconnects power, and resets a

NOTICE: This manual should be left with the owner/user of this equipment. IMPORTANT: This detector must be tested and maintained regularly following NFPA 72 requirements. The detector should be cleaned at least once a year. General Description The 5808W3 photoelectronic smoke/heat detector with built-in wireless transmitter is intended for use with wireless alarm systems that support 5800 series devices. Refer to control/communicator installation instructions for compatibility. The 5808W3 smoke/

During this period we will, at our discretion, repair, replace of refund the price of any part of the gas alarm which is found to be defective in either materials or workmanship providing this occurs under normal use and service. We shall, however, be under noobligation to repair, replace or refund the price of units which are found to be defective in any way due to damage, neglect, unreasonable use or which have been tampered with or found to have been dismantled. Defective units should be retu

Installation Instructions for use with HyperTerminal™ and serial port Parts List Part Numbers Description IPDACT Internet Communicator-Contact ID only. Requires compatible FL panel equipped with on-board or optional DACT. Requires 300mA aux non-reset able power from FACP. Includes cable from panel primary telco port to IPDACT. IPBRKT Bracket for mounting IPDACT inside MS- 9200UDLS common enclosure or in optional HPP-300ULX power supply IPSPLT Splitter for dual phone lines to IPDACT input cable.