Votes - 2, Average rating: 4.5 ( )

Manafacture: First Alert File size: 197.15 kb File name: m08-0142-001e_100s_sa100b.pdf Language of manual:

Battery (DC) operated Smoke Alarms: Provide protection even when This Smoke Alarm is designed to be mounted on any standard wiring junction box to a 4-inch (10 cm) diagonal size, on ether the ceiling or wall (if allowed Disconnecting the power disables the alarm so it cannot electricity fails, provided the batteries are fresh and correctly installed. by local codes). Read “Recommended Locations For Smoke Alarms” and “Locations to Avoid For Smoke Alarms” before you begin installation. sense smoke. This will remove your protection. Instead open Units are easy to install, and do not require professional installation. Tools you will need: Standard Flathead screwdriver. a window or fan the smoke away from the unit. The alarm will However, they do not provide interconnected functionality. AC POWERED reset automatically AC powered Smoke Alarms: Can be interconnected so if one unit THE PARTS OF THIS SMOKE ALARM IONIZATION SMOKE ALARM senses smoke, all units alarm. They do not operate if electricity fails. FOR THE HEARING IMPAIRED AC Smoke Alarms must be installed by a qualified electrician. • ELECTRICAL SHOCK HAZARD: Attempting to disconnect the Parts of the Smoke Alarm AC/DC powered Smoke Alarms: (AC with battery back-up): Can be power connector from the unit when the power is on may result interconnected so if one unit senses smoke, all units alarm. They will in electrical shock, serious injury or death. 1 Mounting slot and screw (1 of 2) operate if electricity fails, provided the batteries are fresh and correctly installed. AC/DC Smoke Alarms must be installed by a qualified electrician. 2 Junction box Input: 120V AC 60Hz, Wireless Interconnected Alarms: Offer the same interconnected .053 A Standby, .059 A Alarm When an interconnected system of AC powered units is in alarm, the 3 Mounting bracket functionality as with hardwired alarms, without wires. Units are easy alarm indicator light on the unit(s) that triggered the alarm will blink to install and do not require professional installation. They provide Strobe: 177 candela minimum rapidly. It will remain OFF on any remaining units. 4 Mounting Bracket Alignment Arrow protection even when electricity fails, provided the batteries are fresh If the unit alarms and you are not absolutely certain of the source of the and correctly installed. The Mounting Bracket The Foam Gasket 5 Mounting slot and screw (1 of 2) STROBE LIGHT OUTPUT FOR WALL & CEILING smoke, get everyone out of the house immediately. Stay calm and follow Smoke Alarms for Solar or Wind Energy users and battery backup Installs onto the junction box. The foam gasket prevents air your family escape plan. Stay as low to the ground as possible, and MOUNTING 6 Wire strip gauge power systems: AC powered Smoke Alarms should only be operated It has a variety of screw slots to fit currents from coming through cover your mouth with a damp cloth. Never open a door before testing The intensity of the strobe light gradually lessens as the angle increases. with true or pure sine wave inverters. Operating this Smoke Alarm with IMPORTANT! PLEASE READ CAREFULLY AND SAVE. most boxes. If a junction box is the junction box and blowing 7 Neutral (white) AC wire it to see if it is hot. Call the Fire Department from outside, and give In other words, the light is brightest directly in front of the strobe light most battery-powered UPS (uninterruptible power supply) products or This user’s manual contains important information about your Smoke not already in place, install one smoke away from the sensor. them your address then name. Read “What To Do In Case Of Fire” for and is progressively less bright to either side. As required by 8 Hot (black) AC wire square wave or “quasi sine wave” inverters will damage the Alarm. Alarm’s operation. If you are installing this Smoke Alarm for use by using standard #12 or #14 gauge It must be installed to comply more information. Underwriters Laboratories Inc. (UL), the following illustrations show how If you are not sure about your inverter or UPS type, please consult with others, you must leave this manual—or a copy of it—with the end user. copper wire. To remove the with UL standards. When 9 Interconnect wire If the unit alarms and you are certain that the source of smoke is not a the strobe light is dispersed. Use them to help you choose where to the manufacturer to verify. mounting bracket from the Smoke installing the foam gasket, line fire—cooking smoke or an extremely dusty furnace, for example—open locate units for the hearing impaired. Alarm base, hold the Smoke Alarm up the cut-outs with the power 10 Foam gasket 9090Angle(In Degrees) PercentLight Intensity05-2530-45505560657075808590100907555454035353030252545450909045450WALLLIGHTLIGHTCEILINGFIGURE 1: Light Output for Ceiling MountFIGURE 2: Light Output for Wall MountSmoke Alarms for the hearing impaired: Special purpose Smoke a nearby window or door and fan the smoke away from the unit. This LISTED TO base firmly and twist mount...

Download now

Please, enter two numbers from picture: