Votes - , Average rating: ( )

User manual Bosch, model FDB2410HIC

Manafacture: Bosch
File size: 189.42 kb
File name: 672060709924.pdf

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

9. No indicator lamps illuminate when START or OPTIONS are pressed. 1. Replace fuse or reset breaker. 2. Repair or replace wire fasteners at dishwasher junction box. 3. Replace control board. 4. Replace control board. 5. Replace motor/impeller assembly. 6. Replace latch assembly. 7. Replace latch assembly. 8. Replace console assembly. 9. Replace console assembly. Motor hums but will not start or run. 1. Motor (bad bearings). 2. Motor stuck due to prolonged non-use. 1. Replace motor assembly. 2. Rotate motor impeller. Motor trips out on internal thermal overload protector. 1. Improper voltage. 2. Motor windings shorted. 3. Glass or foreign items in pump. 1. Check voltage. 2. Replace motor/impeller assembly. 3. Clean and clear blockage. Dishwasher runs but will not heat. 1. Heater element (open). 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Hi-Limit thermostat defective. 1. Replace heater element. 2. Replace control board. 3. Repair or replace. 4. Replace thermostat. Detergent cover will not latch or open. Dishwasher will not pump out. Dishwasher will not fill with water. 1. Latch mechanism defective. 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Broken spring(s). 5. Defective actuator. 1. Drain restricted. 2. Electronic control board defective. 3. Defective drain pump. 4. Blocked impeller. 5. Open windings. 6. Wiring or terminal defective. 1. Water supply turned off. 2. Defective water inlet fill valve. 3. Check fill valve screen for obstructions. 4. Defective float switch. 5. Electronic control board defective. 6. Wiring or terminal defective. 7. Pressure Switch Stuck. Dishwasher water siphons out. 1. Drain hose (high) loop too low. 2. Drain line connected to a floor drain not vented. Detergent left in dispenser. 1. Detergent allowed to stand too long in dispenser. 2. Dispenser wet when detergent was added. 3. Detergent cover held closed or blocked by large dishes. 4. Improper incoming water temperature to properly dissolve detergent. 5. See "Detergent cover will not open." 1. Replace dispenser. 2. Replace control board. 3. Repair or replace. 4. Replace dispenser. 5. Replace dispenser. 1. Clear restrictions. 2. Replace control board. 3. Replace pump. 4. Check for blockage, clear. 5. Replace pump assembly. 6. Repair or replace. 1. Turn water supply on. 2. Replace water inlet fill valve. 3. Disassemble and clean screen. 4. Repair or replace. 5. Replace control board. 6. Repair or replace. 7. Repair or replace. 1. Repair to proper 32-inch minimum height. 2. Install air gap at counter top. 1. Instruct customer/user. 2. Instruct customer/user. 3. Instruct customer/user on proper loading of dishes. 4. Incoming water temperature of 120°F is required to properly dissolve dishwashing detergents. Pots and Pans Normal China Crystal Energy Saver Rinse and Hold Washing Drying Clean Time in Minutes Water Valve Pump Motor Drain Motor Heater Dispensers WATER HEAT DELAY WATER HEAT DELAY Outputs MAIN WASH 5 35 MIN. RINSE 6 8 MIN. RINSE 7 8 MIN. DRY (HOT OR COOL) 19.5 MIN PRE-WASH 1 8 MIN. PRE-WASH 2 8 MIN. PREWASH 3 8 MIN. PREWASH 4 8 MIN. LED Cycle Selection Options Cycles ...