Votes - 2, Average rating: 4
(
)
)
|
manual abstract
1. With the dishwasher switched off, press the On/Off button. The end of programme indicator light flashes (setting mode). In case salt and/or rinse aid refilling is necessary the corresponding indicator lights illuminate. If one of the washing programme indicator lights is on, this means that a washing programme has been set. The setting must be cancelled: press for about 3 seconds the programme selection/cancel button; the indicator light of the set programme turns off and the end of programme indicator light flashes, indicating that the set programme has been cancelled and that the machine is now in setting mode. 2. Press and keep pressed the programme selection/cancel button until programme indicator light 1 flashes and programme indicator light 2 illuminates with a fixed light. Press the programme selection/cancel button again, programme indicator light 1 illuminates with a fixed light and programme indicator light 2 starts flashing. Wait until programme indicator light 1 turns off, programme indicator light 2 goes on flashing and the end of programme indicator light illuminates with a fixed light. This indicates that you have activated the function for the deactivation/activation of the audible signals. The constant illumination of the end of programme indicator light means that the audible signals are activated. 3. To deactivate the audible signals, press the programme selection/cancel button again, the end of programme indicator light turns off indicating that the audible signals are deactivated. 4. To memorise the operation, switch off the machine by pressing the On/Off button or wait for about 60 seconds, after which the machine will automatically return to setting mode. To activate the audible signals again simply follow the above operations until the end of programme indicator light illuminates. Operating instructions Prior to using for the first time Before using your dishwasher for the first time: 1. Ensure that the electrical and water connections comply with the installation instructions 2. Remove all packaging from inside the appliance 3. Set the water softener 4. Pour 1 litre of water inside the salt container and then fill with dishwasher salt 5. Fill the rinse aid dispenser. Note: If you want to use the "3 in 1" combi detergents, read carefully the informations given in "Different kinds of detergents". The water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these minerals and salts, the harder your water is. Water hardness is measured in equivalent scales, Clarke degrees, French degrees (°TH) and mmol/l (millimol per litre - international unit for the hardness of water). The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area. The water softener must be set in both ways: manually, using the water hardness dial and electronically, using the function buttons on the control panel. Operating instructions 12 a) Setting manually 1. Open the dishwasher door. 2. Remove the lower basket from the dishwasher. 3. Turn the water hardness dial to position 1 or 2 (see table). 4. Replace the lower basket. The dishwasher is factory set at position 2. Adjusting the water hardness setting 10 9 8 7 6 3 1 no salt necessary Manually Electronically 2 1 Number of flashes of the “end of programme” indicator light 2 Water hardness 64 - 88 53 - 63 46 - 52 36 - 45 28 - 35 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 13 - 17 1,9 - 2,5 < 5 < 0,7 5 - 12 0,7 - 1,8 23 - 27 18 - 22 3,3 - 3,9 2,6 - 3,2 5 4 10 9 8 7 6 3 1 2 5 4 Clarke degrees 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 19 - 25 < 7 7 - 18 33 - 39 26 - 32 °TH mmol/l Operating instructions b) Setting electronically The dishwasher is factory set at level 5. 1. With the dishwasher switched off, press the On/Off button. The end of programme indicator light flashes (setting mode). In case salt and/or rinse aid refilling is necessary the corresponding indicator lights illuminate. If one of the washing programme indicator lights is on, this means that a washing programme has been set. The setting must be cancelled: press for about 3 seconds the programme selection/cancel button; the indicator light of the set programme turns off and the end of programme indicator light flashes, indicating that the set programme has been cancelled and that the machine is now in setting mode. 2. Press and keep pressed the programme selection/cancel button until programme indicator light 1 flashes and programme indicator light 2 illuminates with a fixed light. Wait until programme indicator light 2 turns off, programme indicator light 1 goes on flashing and simultaneously the end of programme indicator light starts flashing. This indicates that you have activated the electronic setting funct...