Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Turn off the tap. Disposal – Make redundant appliances unusable to prevent subsequent accidents. – Dispose of the appliance in an environmentally friendly manner. en a=Warning Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations. Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed. Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel ( Main switch 0 Door opener 8 Programme selector (retractable *) @ Additional options ** H Display “Check water supply” P Salt refill indicator X Rinse aid refill indicator ` Digital display * depending on model ** Number depending on model Appliance interior 1" Top basket 1* Knife shelf * 12 Top spray arm 1: Bottom spray arm 1B Dispenser for special salt 1J Filters 1R Cutlery basket 1Z Bottom basket 1b Lock for detergent dispenser 1j Dispenser for rinse aid 9" Detergent dispenser 9* Rating plate * depending on model en Water softening system To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 9° Clarke must be softened. The water is softened with salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Water hardness table . & . . # $ . . '. $% . . . !!!"!!!!!!!!!!"!! . . . . . . . . Setting The amount of salt dispensed can be set from ‹ to .. Sal is not required at the set value ‹. – Find out about the hardness value of your tap water. Your water utility company will help you with this. – Set value can be found in the water hardness table. – Close the door. – Rotate the programme selector 8 from the 12 o’clock position anti- clockwise by one notch. – Switch on main switch ( and hold down for at least 3 sec. The current set hardness value is indicated on the digital display ` and the salt refill indicator P flashes (set hardness value was set to level … at the factory). To change the setting: – Rotate programme selector 8. You can select a set value between ‹ and . according to the hardness of your water. – Switch off the main switch ( The chosen setting has now been stored. en Special salt $ Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 1B. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add salt (not table salt). The water is displaced and runs out. * depending on model The salt refill indicator P on the fascia is lit. It goes out as soon as a sufficiently high salt solution has formed. If the set value ‹ is displayed, do not add any salt because salt will not be used during operation of the appliance, the salt display is switched off. If the set values ‚ to . are displayed, salt must be added. Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. Salt refill indicator As soon as the salt refill indicator P on the fascia is lit, top up the salt. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. If the salt refill indicator P is impaired (e. g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under “Setting water softening system” and set the value to ‹. The water softening system and salt refill indicator are now switched off. a=Warnings – Never fill the salt dispenser with detergent. You will destroy the water softening system. – To prevent corrosion, always refill with salt immediately before switching on the appliance. en Rinse aid % As soon as the rinse-aid refill indicator X is lit on the fascia, there is still a rinse-aid reserve of 1–2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. – Open the cover on the rinse-a...
Other models in this manual:Dishwashers - 3VN551ID/18 (1.26 mb)
Dishwashers - 3VN552BD/01 (1.26 mb)
Dishwashers - 3VN552BD/07 (1.26 mb)
Dishwashers - 3VN552BD/09 (1.26 mb)