Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Delicate/Economy For delicate or heirloom dishware and silverware or other special items. Always make sure that the items are dishwasher safe. Refer to the Materials section of this manual for more information. Hand washing may be the best treatment of such items. Quick Wash For lightly soiled items with easy to remove food soils. Rinse and Hold Allows you to rinse the food soil off of a partial load and hold them in the dishwasher until there is a full load. More information on dishwasher cycles is located in the Wash Cycle Information section of this manual. Starting the Dishwasher Open the dishwasher door far enough to expose the control buttons. Press the On/Off button. Press the button for the desired wash cycle. Shut the dishwasher door. The dishwasher will start automatically and continue operating until the end of the selected cycle. Once you start the dishwasher, leave the dishwasher door shut until it finishes the cycle. Interrupting a Cycle NOTE: Should you need to interrupt a cycle (to add or remove an item, to add detergent, etc.), it is best to do so within the first 30 minutes of the cycle. Open the dishwasher door far enough to expose the control buttons. Press the On/Off button. WARNING You could be seriously scalded if you open the dishwasher door quickly during a wash or rinse cycle. Do not fully open the dishwasher door for at least 10 seconds or until water noises stop. Wait at least ten seconds or until water noises stop before opening the dishwasher door. To resume the cycle, press the On/Off button and shut the dishwasher door. Canceling or Changing a Cycle To cancel or change a cycle, open the dishwasher door far enough to expose the control buttons then press and hold for three seconds the two buttons labeled “Cancel Drain” as shown in Figure 16. Figure 16 Cancel Drain Shut the door and wait approximately one minute, then press the On/Off button You may now begin a new cycle. Operating the Dishwasher (continued) Dishware Drying At the end of the cycle the dishwasher will stop and a period of condensation drying will follow. After 12 - 15 minutes of drying: • the cycle countdown display will read “0”. • the “Sanitized” light may appear. See section on Sanitization for more information. NOTE: If your household water supply is too hot, your dishwasher’s heating time may be reduced and the “Sanitized” light may not illuminate. Your Dishwasher Installation Manual has information on the recommended temperature for your household hot water supply. NOTE: To accelerate and enhance drying, open the dishwasher door, pull the top rack a few inches out of the dishwasher, and prop the dishwasher door against the top rack. OPTIDRY™ Low Rinse Agent Compensator This feature senses when the unit is low on rinse agent and automatically increases the drying time. Additional Drying Heat With this option you can raise the temperature of the rinse water and increase the drying time, which will result in improved drying. Press and hold the left “Cancel Drain” button, then press and hold the On/Off button. When the LED display shows a “0” or a “1”, release both buttons. To enable the Additional Drying Heat, press the left “Cancel Drain” button until the LED display shows a “1”. To disable the Additional Drying Heat, press the left “Cancel Drain” button until the LED display shows a “0”. Press the On/Off button to save the setting. “Sanitized” Light When the “Sanitized” light appears, Figure 17 it means that the dishware and kitchenware that was just washed has been sanitized. The Cycle Completion Signal The Cycle Completion Signal is a tone that sounds when your dishwasher finishes washing and drying your dishes. You can either disable the tone or set the volume. To change the Cycle Completion Signal Volume: 1. Open the dishwasher door far enough to expose the control buttons. 2. Press and hold the right “Cancel Drain” button then press and hold the On/Off button. 3. When the light on the “Cancel Drain” button you are pressing illuminates and the tone begins to sound, release both buttons. 4. Press the right-most “Cancel Drain” button until the tone is either at the desired volume or is silent. 5. Press the On/Off Button. 6. Shut the dishwasher door. The Cycle Completion Signal is now set, and you may wash your dishes as usual. Unloading the Dishwasher Unload the bottom rack first. Unload the silverware basket(s). They are easily removed for unloading. Unload the top rack. If the Extra Tall Item Sprinkler was installed, return the dishwasher to its normal condition (see the Loading Extra Tall Items instructions in the “Loading the Dishwasher” section of this manual). Care and Maintenance Maintenance Tasks Certain areas of your dishwasher require occasional maintenance. The maintenance tasks are easy to do and will ensure continued superior performance from your dishwasher. These tasks are: • Winterizing Your Dishwasher • Wiping up Spills and Splash-out • Clean the Stainless Steel Inner Door and Tub • Check...
Other models in this manual:Dishwashers - SRV53C03UC/36 (4.01 mb)
Dishwashers - SRV53C03UC/44 (4.01 mb)
Dishwashers - SRV53C13UC/01 (4.01 mb)
Dishwashers - SRV53C13UC/46 (4.01 mb)