Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Dry all Gentle 40. Utensils and cutlery Lightly soiled Prerinse Clean 40. Intermediate rinse Final rinse 55. Dry . Express Wash Half load Extra drying Quick 45. Utensils and cutlery Lightly soiled Clean 45. Intermediate rinse Final rinse 55. Extra drying Prerinse Lightly soiled Prerinse none Programme selection You can select a suitable programme according to the type of utensils and degree of soiling. Information about comparability tests The conditions for running comparability tests can be found on the supplementary sheet “Information for comparability tests”. en Additional options * depending on model Additional options 3 can be set with the buttons. Express Wash (VarioSpeed) * The >>Express Wash<< function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. To obtain optimum cleaning and drying results at a reduced running time, water and energy consumption are increased. Half load * If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. Hygiene * The temperature is increased during the rinsing process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. IntensiveZone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. . . * . . . . . Washing the dishes Programme data The programme data (consumption values) can be found in the summary of instructions. This data refers to normal conditions and the water hardness set value 2. Different influencing factors such as water temperature or mains pressure may result in deviations. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance Turn on the tap fully. Open the door. Switch on ON/OFF switch 1 . The display of the last selected programme 4 flashes. This programme remains selected unless another programme is selected with the button < 5 or button > 6 . Press the Start button 9 . Close the door. The programme starts running. en Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. Switch on ON/OFF switch 1 . Keep pressing the Preselected starting time button 2 until the appropriate display 3 h, 6 h or 9 h is lit. Press Start button 9 . The preselected starting time is activated. To delete the preselected starting time, keep pressing the Preselected starting time button 2 until none of the displays 3 h, 6 h or 9 h is lit. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the End display 8 is lit. The end of the programme is also indicated by an acoustic signal. The buzzer volume can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit. (see water hardness table). Factory setting: 2. This function can be changed as follows: Open the door. Switch on ON/OFF switch 1 . Hold down button > 6 and press Start button 9 until the End display 8 and salt refill indicator 11 flash. Release buttons. Keep pressing button > 6 until the salt refill indicator 11 and rinse aid refill indicator 10 flash. Release buttons. The refill indicator 11 flashes and the displays 10 and A are B lit (= setting 2). The set buzzer volume can be heard. Change the setting as follows: ress button < 5 until the required setting has been selected. Press Start button 9 . The displays go out. The selected setting is saved. Close the door. Switching off the appliance Short time after the end of the programme: Open the door. Switch off ON/OFF switch 1 . Turn off the tap (not applicable if Aqua-Stop fitted). Remove the utensils when they have cooled down. Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme Open the door. Switch off ON/OFF switch 1 . The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring ope...
Other models in this manual:Dishwashers - SMVATE02NL/01 (2.38 mb)