No other settings on the appliance are required. If in doubt, please contact the detergent manufacturer, especially if: the utensils are very wet at the end of the programme. limescale forms. Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness. Note Even if the rinse aid refill indicator is lit, the rinse programme runs correctly when 3in1 products are used. If the rinse aid refill indicator 5 is defective and you would like to switch it off, proceed as follows: Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 5 on or off. This function can be changed as follows. Hold down the programme button 3 and press the main switch 1 until the digital display lights up, then release the buttons. 8 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button 3 , you can switch off or switch on the rinse aid indicator. Switch off the main switch 1 ; the setting is saved. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on. aus Programme overview This overview lists the max. possible number of programmes. The programmes supplied with your appliance are indicated on the fascia. delicateNon- delicate Mixed Mixed Type of crockery e.g. china, pots/pans, cutlery, glasses, etc. Type of food remains Amount of food remains Condition of food remains Wash programme Programme- sequence Normal 45 Quick 45 Auto 55 /65 Intensive 70 Pre-rinse Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. very littlea littlea lot stuck on hard loosely attached Drying Rinse aid 70 First rinse Wash 70 Pre-rinse 50 Second rinse Drying Rinse aid 45 Wash 45 Rinse aid 55 Main rinse Wash 45 Pre-rinse Third rinse Pre-rinse Drying The programme sequence isoptimized and adapted with howthe appliance is loaded and howdirty the dishes are. medium Main rinse Programme Laboratory measured value in accordance with AS/NZS 2007 135 1,75 12 30 0,80 – 20 10 20 0,05 4 – 85-140 1,00-1,60 – 9-19 details Duration in minutes Electricity consumption in kWh Water consumption in litres with Aquasensor 140 0,60 – 13,7 aus Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Aqua sensor * * some models The Aquasensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. When the Aqua sensor is active, “clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way water consumption can be reduced by approx. 4 litres. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed The numerical display 8 shows the expected duration of the programme. Close door. The programme starts automatically. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device’s door. Only open the dishwasher door when the light point has disappeared. In the case of built-in dishwashers with flush front the light point will not be visible. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. Time delay * * on applicable models You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button 3 until the digital display 8 jumps to . Keep pressing the timer programming button u...

Other models in this manual:
Dishwashers - SL6KLN1AU/13 (2.27 mb)
Dishwashers - SL6KLN1AU/18 (2.27 mb)