Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Extra dry* If you press the “Extra dry” button, you will receive a higher temperature in all programmes in the final rinse and therefore an improved drying result. (please note that higher temperatures might have an effect on delicate items). en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Therefore you should occasionally have a careful look inside your dishwasher. Overall condition of the machine Check spray arm for grease and limescale deposits. If you find such deposits: Fill the detergent dispenser with detergent, start the appliance without utensils in the programme which has the highest wash temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the door seal with a damp cloth to remove deposits. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Attention! Never use other chlorinated household detergents! Health hazard! Special dishwasher salt Check the LOW SALT indicator 9 . Top up with salt, if required. Rinse-aid As soon as the rinse-aid refill indicator lights up on the control panel 8 , refill with rinse aid. Filters Waste which is deposited on the filters 28 may result in a blockage. After each washing cycle check the filters for residue. Unscrew the filter cylinder and remove the filters. The filters are permanently attached to each other and cannot be dismantled. Remove large foreign objects. Clean the filters under running water. Re-installation: Insert the filters and screw the filtercylinder tight. en Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 22 and 24 and the arm mountings . Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm 24 upwards and lift it off. Unscrew the upper spray arm 22 . Clean both spray arms under running water. Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. Spray arms Waste water pump * * some models Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case: Set the main switch 1 to OFF. Scoop out any water. Remove the filters 28 . Remove the cover. en Check the inner compartment for foreign objects and, if required, remove foreign objects. Re-insert the cover. Re-insert the filters and screw into position. Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer. Not only does this save costs, but it also means that the appliance is available for use again that much sooner. The following list of common occurrences and their remedies should help you identify the causes of most problems. Problems ... Attention Remember: Repairs may be carried out by a technician only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. en ... when the appliance is switched on The appliance does not start. The mains fuse has tripped. The appliance plug has not been inserted. The appliance door has not been shut properly. The tap has not been turned on. The filter on the water supply hose is blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Then clean the filter which is situated at the connection of the supply hose. Finally, restore the power, turn on the tap and switch on the appliance. ... with the appliance itself Lower spray arm rotates with difficulty Spray arm is blocked by small items or food remains. Lid in detergent compartment cannot be closed Detergent compartment has been overfilled. Mechanism is clogged with remnants of detergent. Indicator lamps do not extinguish after washing has finished. Indicator lights flash after the programme has started. No programme selected. Indicator lamps do not extinguish after washing has finished Main switch is still set to ON. Remnants of detergent stuck inside dispenser Compartment was damp when it was filled up with detergent. Compartment must be dry before detergent is added. “Check water supply” display lights up. Tap turned off. Water supply interrupted. Filter in the water supply blocked. Supply hose kinked. Water remains inside appliance after programme has ended Blockage or kink in drainage hose. Pump is jammed. Filters are blocked. The programme is still running. Wait for the programme to end. Perform “Reset” function. The door opens and closes incorrectly on appliances which are designed to be built-in. The attached door panel is not the correct weight. Observe the weight indicated in...
Other models in this manual:Dishwashers - SGS44E72EU/01 (728.88 kb)