Votes - 0, Average rating: 0
(
)
)
|
manual abstract
The capacity of the detergent container is 15 ml up to the bottom line and 25 ml up to the middle line. When the compartment is full it contains 40 ml. Reduce costs! If your dishes are only moderately dirty, you may be able to use less detergent than recommended. Close the lid on the detergent compartment. Press down the lid (1) until it clicks shut (2). If the detergent dispenser 3028 is still closed, press the lock to open the detergent dispenser. Adding detergent Fill the dispenser 30 with detergent. Please observe the manufacturer’s instructions printed on the detergent packaging when determining the correct dosage. Important Due to the different solvency properties of the detergent tablets supplied by various manufacturers, the cleaning efficiency of the detergent may not be fully utilised by short programmes. It is recommended to use washing powder for these programmes. When you select the Auto 65-75. programme, tip an extra 10–15 ml of detergent onto the inside surface of the door. If you are using detergent in tablet form, read the manufacturer’s recommendations on the packaging in order to determine where the tablets should be placed inside the dishwasher (e.g. in cutlery basket, detergent compartment, etc.). Make sure that the lid on the detergent compartment is closed, even if you are using tablets. en auto 3in1 The use of so-called combined detergent products may make the use of rinse aid and/or salt unnecessary. There are currently several types of combined detergent products available. 2in1: They contain detergent and rinse aid or salt function. 3in1: They contain detergent, rinse aid and salt function. 4in1: They contain a detergent, rinse-aid, salt function and an additional glass protection component. In addition, other combined products with a comparable effect are offered according to the manufacturer. >>> Always check the type of detergent or combined product which you are using! Always follow the operating instructions or the information on the packaging. The rinse programme is automatically adjusted in order to obtain the best possible rinsing and drying result. Observe the following important information if using combined cleaning products: Regeneration salt is not required up to a water hardness of 21 dH (37 fH, 26 Clarke, 3.7 mmol/l) only. No other settings on the appliance are required. Salt is still required if the water hardness is above 21 dH (37 fH, 26Clarke, 3.7 mmol/l). Fill the salt dispenser with salt 24 and select setting 6 on the water softening system. If in doubt, please contact the detergent manufacturer, especially if: the utensils are very wet at the end of the programme. limescale forms. Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of salt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness. Note Even if the rinse aid and/or salt refill indicator is lit, the rinse programme runs correctly when 3in1 products are used. If the rinse aid refill indicator 6 or salt refill 5 indicator is defective and you would like to switch it off, proceed as follows: Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 6 on or off. This function can be changed as follows. Hold down the programme button 3 and press the main switch 1 until the digital display lights up, then release the buttons. 9 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button 3 , you can switch off or switch on the rinse aid indicator. Switch off the main switch 1 ; the setting is saved. en Switching the salt refill indicator / water softening system off and on Hold down the programme button B and switch on the main switch 1 , then release the buttons. The illuminated button B and the factory-set value on the digital display flash. To change the setting: press the programme button B . Each time the button is pressed, the set value increases by one; when the value is reached, the display jumps back to (the salt refill indicator / water softening system has been switched off). Switch off the main switch 1 . The set value is stored within the device. Approx. 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. en Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Delicate Type of dishes e.g. porcelain pans, cutlery, glasses, etc. Non- s...
Other models in this manual:Dishwashers - SGIKBO2/13 (2.44 mb)
Dishwashers - SGIKBO2/18 (2.44 mb)
Dishwashers - SGIKBO2/21 (2.44 mb)