Votes - 0, Average rating: 0
(
)
)
|
manual abstract
The amount of salt required depends on the degree of hardness of your tap water (see table at right for more information). For the water softening system to function properly, it will need to use dishwasher water softener salt. The amount of salt dispensed can be set from “H:00” to “H:07”. Salt is not required at H:00 (this is the default factory setting - see table at right). • Open the door (for hidden controls only). • Turn the unit on using the [ON/OFF] button . • Hold down the “A” button (see page 4) and press [START] until the tap water hardnessppm CaCO./l set value at dishwasher use salt 0 - 110 H:00 no 120 - 140 H:01 yes 150 - 180 H:02 yes 190 - 210 H:03 yes 220 - 290 H:04 yes 300 - 370 H:05 yes 380 - 540 H:06 yes 550 - 890 H:07 yes Default setting from factory is H:00 display indicates “H:00”. • Release both buttons. • Press the “B” button to select the desired setting. • Save the selected setting by pressing [START]. • Close the door (for hidden controls only). NOTE: For information on how to use the water hardness test strip, provided in the detergent sample kit, please see below. Using a water hardness test strip Establishing the water hardness Setting of water softener Fill with Salt Dip the test strip briely into tap water for a second. Shake of excess water and compare after approxi- mately 1 minute. After 1 minute the red discoloration of the test areas will show you the correct setting. Alignment of Softening Unit Fill salt into the salt container 0 H:00 no 1 H:00 no 2 H:02 yes 3 H:04 yes 4 H:06 yes Salt Reill the salt container (use the supplied funnel to pour) right before turning on the unit to ensure that salt overlow is immediately washed away. This prevents corrosion. • Open the screw cap of the salt container. • Fill the container with water (only required when turning on the unit for the irst time). • Add salt (dishwasher salt) until the water is displaced and runs out. • Reill with salt as soon as the salt reill indicator “ ” or “Salt” LED is lit. WARNING: Never ill the salt dispenser with detergent. It will destroy the water softening system. To prevent corrosion, reill with salt and immediately begin any cycle. NOTE: Reill salt in the appliance only when the salt reill LED or symbol is lit. Do not use salt tablets or any salt other than dishwasher water softening salt. For more information about ordering salt please contact Customer Service. You can buy special dishwasher salt as spare part 469559 or as accessory SGZ9091UC. * * model dependent Detergent Use only detergent speciically designed for dishwashers. For best results, use fresh dishwashing detergent. The dishwasher is also equipped with a tablet collecting tray, designed to fully dissolve detergent tabs. NOTICE: To avoid dishwasher damage, do not use hand dishwashing products in your dishwasher. Your dishwasher uses less water, therefore you need to use less detergent. With soft water, 1 tablespoon (15ml) of detergent will clean most loads. The detergent dispenser cup has lines that measure detergent to 1 tablespoon (15ml) and 1.75 tablespoons (25ml). 3 tablespoons (45ml) of detergent will completely ill the detergent dispenser cup. NOTE: If you do not know the hardness of your water supply, use 15ml of detergent. Increase the amount of detergent, if necessary, to the least amount required to get your dishware and kitchenware clean. To Close: Place inger as shown in igure at right, slide forward, then press down irmly until you hear it click into place. To Open: Push button as shown in the igure at far right and cover slides open. Recommended Detergent AmountWater Type WashCycleUnit Hard Water/Heavy Soil Medium Water/Medium Soil Soft Water/Light Soil PowerScrub ml 45 45 25-45 Tbsp 3 3 1.75 to 3 AutoWash ml 25-45 25 15-25 Tbsp 1.75 to 3 1.75 1 to 1.75 RegularWash ml 25-45 25 15-25 Tbsp 1.75 to 3 1.75 1 to 1.75 Delicate ml 25 15-25 15 Tbsp 1.75 1 to 1.75 1Quick/GlassCare ml 25 15-25 15 Tbsp 1.75 1 to 1.75 1 3TBSMAX2TBS(25ML) 1TBS(15ML) Add Detergent To close the cover To open the cover 8 7 Rinse agent in If the To achieve proper drying, always use a liquid rinse agent, even if your detergent contains a rinse agent or drying additive. Rinse Agent Dispenser Open the rinse agent dispenser by lifting the tab with your thumb. NOTE: The dishwasher indicates low rinse agent either by showing the symbol the display, or illuminating the reill rinse agent LED (model dependent). symbol is displayed or the LED is on, you need to reill the rinse agent dispenser. Add liquid rinse agent to the dispenser as shown until the rinse agent reservoir is full. Wipe up ...
Other models in this manual:Dishwashers - SGE63E06UC/32 (7.17 mb)
Dishwashers - SHE68E05UC/32 (7.17 mb)
Dishwashers - SHE68E15UC/32 (7.17 mb)
Dishwashers - SHV58E13UC/32 (7.17 mb)