Votes - 0, Average rating: 0
(
)
)
|
manual abstract
containing little or no lime, otherwise water stains will be left behind on crockery and glasses, etc. If the tap water exceeds a certain level of hardness, it must be softened, i.e. decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener (see introduction) Filling the special salt container How the salt works While washing is taking place, salt is automatically rinsed out of the salt container into the water softener where it dissolves the lime in the water. The dissolved lime is pumped out of the dishwasher. The water softening system is then ready for the next load. This process of regeneration can only function when the salt is dissolved in water. Unscrew the lid on the salt container 24 . Before you use the dishwasher for the first time, pour approx. 1 litre of water into the salt container. Use the enclosed salt filler. Refill with salt (do not use edible salt) until the salt dispenser is full (max. 1.5 kg). When the salt dispenser is being refilled, water is displaced and drains away. Therefore always refill the salt dispenser immediately before switching on the dishwasher (to prevent corrosion). As a result, the overflowing salt solution will be immediately diluted and rinsed out. Then remove salt residue from the filler area and screw on the dispenser cover, ensuring that it is not fitted askew. en The LOW SALT indicator 5 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated. Note When the control is set to , it is not necessary to fill up with salt as none will be consumed while the dishwasher is operating. The LOW SALT indicator is switched off. If the control is set between and , then salt must be added to the dispenser. Do not pour detergent into the container for special salt. This would destroy the water softener. Salt refill indicator As soon as the salt refill indicator 5 is lit on the control panel, refill with salt immediately before the next rinse cycle. en Adding rinse aid Rinse aid is used in the rinsing cycle to ensure clear glasses and stain-free utensils. Open the lid of the rinse-aid dispenser 29 by pressing the button on the rinse-aid lid and lifting up the lid. Pour the rinse-aid into the filler hole until the level indicator turns dark. Close the lid, ensuring that you hear it snap closed. rinse–aid control Note Use only rinse aid for domestic dishwashers. Spilt rinse aid may result in excessive foam formation in the next rinse cycle. Therefore, remove any spilt rinse aid with a cloth. Convenient rinse-aid filling procedure with half-open door Open the rinse-aid lid and pull out the hinged filling aid until it locks into position. Slowly fill with rinse aid but do not overfill. Close the rinse-aid lid until it clicks shut. Set Amount of Rinse Aid The amount of rinse aid is set at the factory to 4. Only change this setting if streaks or water stains remain on the dishes. Hold the Programme button 3 and press the main switch 1 . Release both buttons. In order to change the setting, press the Programme button 3 . Each time you press the button the value increases by one step; once a value of is reached the indicator jumps back to (Off: The rinse aid fill indicator 6 does not show a need to refill). Switch off the main switch 1 . The set value is stored within the device. Note Only switch off the rinse aid indicator if you are using cleaning products with integrated rinse aid! en Unsuitable dishes You should not clean the following items in your dishwasher: Cutlery and dishes made of wood. They will leach out and become unsightly; the utilised adhesives are also not suitable for the dishwasher temperatures. Delicate decor glasses, craft dishes and vases, special antique or irreplaceable dishes. These decor items are not dishwasher-safe. Plastic parts, copper and tin dishes sensitive to hot water are not suitable either. Overglazed patterns, aluminium and silver parts tend to become discoloured and fade during the rinsing cycle. Even some types of glass (e.g. crystal glass objects) may become cloudy after many rinse cycles. Completely absorbent materials, such as sponges and cloths must not be cleaned in the dishwasher either. Recommendation: In future buy only dishes which are identified as dishwasher-safe. Note Dishes which are soiled with ash, wax, lubricating grease or ink must not be cleaned in the dishwasher. Damage to glassware and other dishes Possible causes: type of glass or manufacturing process chemical composition of detergent water temperature and duration of dishwasher programme. Suggested remedy: Use glassware or porcelain dishes that have been marked ’dishwasher–proof’ by the manufacturer. Use a mild detergent that is described as ’kind to dishes’. If...
Other models in this manual:Dishwashers - SE66T371EU/07 (2.26 mb)
Dishwashers - SE66T371EU/08 (2.26 mb)