Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Aquasensor The Aquasensor is an optical measuring device with which the cloudiness of the water in the dishwasher is measured. A photoelectric sensor is used to detect the degree of soiling in the water, caused by dissolved food particles such as egg, fat and rolled oats, etc. The Aquasensor functions during all programmes that include a pre-rinse cycle. If the water is still “clean” at the end of the pre-rinse cycle, then the same water is used for the following wash cycle. If the water is dirty, it is pumped out of the dishwasher and replaced by fresh water. The effect is to reduce water consumption by approx. 4 litres when the dishes are only “slightly” dirty. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 9 is pressed The numerical display 6 shows the expected duration of the programme. Close door. The programme starts automatically. Programme progress indicator 10 Your dishes are being washed. Your dishes are being dried. The programme has ended. en End of programme The end of programme is indicated by a buzzer. This function can be changed as follows: Hold down the Time delay programme button 51 and switch on the Main switch , then release the buttons. The Time delay button 5 flashes and the digital display indicates the value (loud) which was set at the factory. To change the setting: Press the Time delay programme button 5 . Each depression of the button increases the set value by one; when is reached, the display jumps back to (off). Switch off the Main switch 1 . The set value is stored in the appliance. Switching the dishwasher OFF Several minutes after the programme has ended: Open the door when the programme has ended. Set main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. Interrupting the programme Open the door. Caution! There is a risk of water squirting out from inside the appliance. Do not open the door fully until the spray arm has stopped rotating. Set main switch 1 to OFF. Indicator lights extinguish. The programme is retained in the dishwasher memory. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion. In order to continue with the stored programme, set the main switch to ON again and close the door. Programming the timer You can delay the start of a programme in increments of one hour for up to 19 hours. Switch dishwasher ON. Immediately press the TIMER button 5 . The numerical display 6 changes to . Press the TIMER button as many times as necessary until the numerical display shows the required delay. To erase the time delay setting, keep pressing the TIMER button until appears in the numerical display. You can change your programme selection as often as you like during the intervening period before the dishwasher starts up. Pre-Soak * * on applicable models The Pre-Soak programme option serves to perform a pre-soak cycle before the main programme. This cycle enables cookware, e.g. pans, bowls, etc. to be pre-soaked and pre-rinsed in the lower rack. If you wish to pre-soak the dishes, this programme option must be selected by pressing the “Pre-Soak” button 3 before the programme starts. The recommended detergent amount is approx. 5 g poured onto the inside of the door. en Quick * * on applicable models Pressing the “Quick” button 4 provides a short wash cycle by curtailing the drying phase and the washing time. The washing and drying performance will be reduced with the Quick programme option. Time-remaining indicator The time-remaining indicator is self-learning. When the programme begins, it displays the estimated duration of that programme. This figure is based upon the duration of the previous programme, or if the dishwasher is being used for the first time, the duration of the programme used for testing the appliance in the factory. While the programme is running, the indicator shows the amount of time before the programme ends. The time remaining is also adjusted to account for the temperature of the water supply and the number of dishes. Intensive drying function Activating the intensive drying function increases the temperature during the rinse-aid stage which gives better drying results. Press and hold the A programme button, and set the main switch 1 to ON. Release both buttons. Either (ON) or (OFF) flashes in the numerical display 6 . Press the A programme button to change the setting. Set the main switch 1 to OFF. The new setting is stored in the dishwasher memory. Cancel programme (Reset) Only when the master switch is ON. Press the A and C buttons simultaneously, and hold them pressed for approx. 3 seconds. The numerical display shows . Close the door...
Other models in this manual:Dishwashers - SE25243GB/37 (2.41 mb)
Dishwashers - SE25843GB/17 (2.41 mb)
Dishwashers - SE25843GB/37 (2.41 mb)