Votes - 0, Average rating: 0
(
)
)
|
manual abstract
8 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button 3 , you can switch off or switch on the rinse aid indicator. Switch off the main switch 1 ; the setting is saved. Switching the salt refill indicator / water softening system off and on Hold down the programme button B and switch on the main switch 1 , then release the buttons. The illuminated button B and the factory-set value on the digital display flash. To change the setting: press the programme button B . Each time the button is pressed, the set value increases by one; when the value is reached, the display jumps back to (the salt refill indicator / water softening system has been switched off). Switch off the main switch 1 . The set value is stored within the device. Approx. 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. en Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Type of dishes Rinse if the utensils have been left several days prior to washing in the dishwasher. Coffee, cake, milk, sausage, cold drinks, salads Soups, souffles, potatoes, pastries, rice, eggs, fried food Delicate e.g. porcelain pans, cutlery, glasses, etc. Type of food remnants e.g. Programme- sequence The programme sequence is optimised and adjusted according to the degree of soiling on the utensils. Dry Dry Clean 65 Interme- diate rinse Clean 50 Prerinse Clean 55 Interme- diate rinse Clean 45 Prerinse Coffee, cake, milk, sausage, cold drinks, salads Soups, potatoes, pastries, rice, eggs, fried food Non- sensitive Mixed Wash programme Very little LittleLarge High NormalLightly Adhesive Amount of food remnants State of food remnant Auto 65–75 Auto 55–65 Auto 35–45 Eco 50 Quick 45 Prerinse Low Normal Mixed en Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The programme specifications can be found in the summary of instructions. Programme specifications refer to normal conditions. Greater deviations may occur due to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. A light barrier can detect dissolved food remnants in the water, e.g. egg, fat and oats. The Aqua sensor is used according to the programme. When the Aqua sensor is active, ”clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way the water consumption is reduced by approx. 4 litres for utensils which are ”less” dirty. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed The numerical display 8 shows the expected duration of the programme. Close door. The programme starts automatically. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device’s door. Only open the dishwasher door when the light point has disappeared. In the case of built-in dishwashers with flush front the light point will not be visible. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. en Time delay * * on applicable models You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button 3 until the digital display 8 jumps to . Keep pressing the timer programming button until the required time is displayed. To delete the timer progr...
Other models in this manual:Dishwashers - SE25T850GB/04 (2.26 mb)
Dishwashers - SE25T850GB/08 (2.26 mb)
Dishwashers - SE26T251EU/01 (2.26 mb)
Dishwashers - SE26T251EU/04 (2.26 mb)