Votes - 0, Average rating: 0
(
)
)
|
manual abstract
End of programme The programme has ended when a figure appears in the numerical display 8 . Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. en Interrupting the programme Set main switch 1 to OFF. Indicator lights extinguish. The programme is retained in the dishwasher memory. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion. In order to continue with the stored programme, set the main switch to ON again. Terminating the programme (Reset) Only when the main switch is on: Rotate programme selector to the Reset position. The digital display indicates after approx. 3 sec. The programme sequence lasts approx. 1 min. When the programme has run, switch off the main switch 1 . To restart, rotate the programme selector 3 to the required programme. Switch on the main switch 1 . The programme sequence starts automatically. Changing the programme It is possible to change the programme within 2 minutes after you have switched the dishwasher on. Should it be necessary to change the programme after this period, the programme cycle that has already been begun (e.g. washing) will be completed first of all. The new remaining time displayed is the sum of the remaining time from the preceding programme cycle and the remaining time attributable to the new programme that has been selected. Intensive drying By activating the “Intensive drying” function, the final rinse will produce a higher temperature in all programmes resulting in an improved drying result (please note that higher temperatures might have an effect on delicate items). Close the door. Hold down button B and switch on main switch 1 . Release both buttons. The digital display 8 indicates (on) or (off) and button B flashes. To change the setting, press button B . Switch off the main switch 1 ; the chosen setting has now been stored. en Additional functions * * on some models additional functions can be set with the buttons. Pre-Soak * The Pre-Soak programme option serves to perform a pre-soak cycle before the main programme. This cycle enables cookware, e.g. pans, bowls, etc. to be pre-soaked and pre-rinsed in the lower rack. If you wish to pre-soak the dishes, this programme option must be selected by pressing the “Pre-Soak” button before the programme starts. The recommended detergent amount is approx. 5 g poured onto the inside of the door. Time reduction/ time saving * Pressing the “Time reduction/time saving” button provides a short wash cycle by curtailing the drying phase and the washing time. The washing and drying performance will be reduced with the Time reduction/time saving programme option. Half load* If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “Half load”. The “half load” additional function saves water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. Extra dry* If you press the “Extra dry” button, you will receive a higher temperature in all programmes in the final rinse and therefore an improved drying result. (please note that higher temperatures might have an effect on delicate items). Time delay * h. You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button until the digital display 8 jumps to . Keep pressing the timer programming button until the required time is displayed. To delete the timer programming, keep pressing the button until is displayed. You can change your programme selection at any time until the programme starts. Saving time (VarioSpeed) * The >>Save time<< function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. The particular change in the running time is indicated on the time remaining display. To obtain optimum cleaning and drying results at a reduced running time, water and energy consumption are increased. en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine Check washing chamber for grease and limescale deposits. If you find such deposits: Fill the detergent dispenser with detergent, start the appliance without utensils in the programme which has the highest wash temperature. Clean the appliance with d...
Other models in this manual:Dishwashers - SE24E760TR/13 (2.42 mb)
Dishwashers - SE24E760TR/16 (2.42 mb)
Dishwashers - SE24E860TR/08 (2.42 mb)
Dishwashers - SE24E860TR/09 (2.42 mb)