Votes - 4, Average rating: 3.5 ( )

Manafacture: KitchenAid File size: 874.92 kb File name: Language of manual:

2. Secure the attaching tabs to the cabinet using #8 Phillips head screws. NOTE: Before securing the dishwasher, confirm that the chassis is still properly aligned. 6 3. Pull one of the bottom drawer runners all the way out. Make sure the latches on the back of the drawer runner are facing forward. 4. If the bottom drawer was rotated, rotate the drawer to unwind the hoses and then put the drawer on the extended runner, making sure the hoses are looping upward. 5. While holding on to the drawer, fully extend the remaining drawer runner. Follow the procedure in step 3 to place the drawer on the remaining runner. 6. Make sure both runner clips have snapped into place. If they have not, pull the runner clips forward until they do. 7. Close the drawer. side mounting bracket drawer runner latch latch bracket runner clip Option 2: Attach dishwasher (bottom mount) 1. Temporarily reinstall drawer and remove entire dishwasher from cavity. 2. Drill a 3/16” diameter pilot hole at each of the three locations marked. 3. Replace dishwasher in opening and realign with chassis mark. 4. Remove drawer and install the three 1” hex head screws and the three 9/16” washers (all three screws and washers must be used) using a minimum 20 in/lb torque. 5. Reinstall the drawer, following steps 3 through 7 in Option 1. 6. Check unit for side-toside movement. If it moves, remove the drawer and retighten the screws. Then reinstall the drawer. Bottom mount hole locations Hex head screws and washers 7 Option 2: Garbage disposal connection 1. Route the drain hose as shown and press the hose into the drain hose support. 2. Decide if the drain hose needs to be trimmed. If it does, trim it. NOTE: The drain hose connector must not support the weight of excess hose length. Keep hose as fully extended as possible. 3. Slip a wire clip over the drain hose. Push the hose into the drain hose connector firmly, 5 clicks. 4. Position the wire clip between the two positioning ribs on the drain hose connector. 5. Attach the drain hose connector to the garbage disposal using the supplied hose clamp. 6. Attach the drain hose support bracket to the cabinet with a #8 Phillips head screw at the height shown below. IMPORTANT: A drain loop must be provided as shown in the Installation Instructions. Keep hoses as fully extended as possible to prevent sagging. Any excess length of hose should be kept on the dishwasher side of the drain loop. Install the Drain Hose A drain hose extension kit, part no. 8194400, will extend the drain hose to a length of up to 141 ...” (360.05 cm). Do not extend beyond this length. The maximum drain height is 37 ...” (95.25 cm). Option 1: Sink drain waste tee connection 1. Route the drain hose as shown and press the hose into the drain hose support. 2. Decide if the drain hose needs to be trimmed. If it does, trim it. NOTE: The drain hose connector must not support the weight of excess hose length. Keep hose as fully extended as possible. 3. Slip a wire clip over the drain hose. Push the hose into the drain hose connector firmly, 5 clicks. 4. Position the wire clip between the two positioning ribs on the drain hose connector. 5. Attach the drain hose connector to the waste tee using the supplied hose clamp. 6. Attach the drain hose support bracket to the cabinet with a #8 Phillips head screw at the height shown below. IMPORTANT: A drain loop must be provided as shown in the Installation Instructions. Keep hoses as fully extended as possible to prevent sagging. Any excess length of hose should be kept on the dishwasher side of the drain loop. drain hose support water supply waste waste tee waste garbage disposal valve valve water supply 8" (20.3 cm) min. bend radius from valve 8" (20.3 cm) min. bend radius from valve 6" (15.2 cm) minimum 6" (15.2 cm) minimum wire clip drain hose connector wire clip drain hose connector drain hose support 27-1/2" – 32-1/4" (70 cm – 82 cm) 27-1/2" – 32-1/4" (70 cm – 82 cm) Keep drain hose straight, as shown. Keep drain hose straight, as shown. Option 3: Air break connectior 1. Route the drain hose as shown. 2. Decide if the drain hose needs to be trimmed. If it does, trim it. 3. Slip a wire clip over the drain wire clip hose. Push the hose into the drain hose connector firmly, 5 clicks. 4. Position the wire clip between drain hose connector the two positioning ribs on the drain hose connector. 52 Attach the drain hose connector to the air break using the supplied hose clamp. air break waste valve drain hose connector water supply 8" (20.3 cm) min. bend radius from valve Connect to Water Supply 12 Install the flat seal washer on the end of the inlet hose. Connect the inlet hose to the water supply valve. Tighten securely. 22 Turn the water valve on and check for any leaks. flat seal washer valve inlet hose Install Drawer Front Panel Option 1: Install standard front panel (on some models) 12 Remove front panel from box and discard all shipping material. 22 Remove the tape securing the connector and wires f...

Download now

Please, enter two numbers from picture: