Votes - 5, Average rating: 4.2 ( )

Manafacture: Avanti File size: 1.02 mb File name: Language of manual:

• Screw the faucet adapter onto (or into) the faucet tap. Check for leaks (use Teflon tape to eliminate if necessary). • Connect the six-sided connection of the drain hose to the drain port connection on the back of the dishwasher cabinet. Do not over-tighten (to avoid damage to threads). • Connect the star-shaped connection of the inlet hose to the inlet port on the back of the dishwasher cabinet. Do not over-tighten (to avoid damage to threads). • Connect the circular connection of the drain hose onto the longer (bottom) male connection on the quick connect. • Connect the circular connection of the inlet hose onto the shorter (top) male connection on the quick connect. • Attach the quick connect onto the faucet adapter, by pulling down the outer locking collar on the quick connect, while pushing the quick connect upward onto the faucet adapter. • When the quick connect snaps onto the faucet adapter, release the locking collar. Verify the connection is secure. • Slowly open the hot water line and check for any sign of water leaks at all hose connections. If leaks are located, immediately close the water supply and repair the hose connections. IMPORTANT • Once you open the water supply line, (even if it is closed immediately thereafter), the inlet hose will be pressurized. • To relieve water pressure from inside the inlet hose, (make sure the water line (faucet) is closed): press and hold the red pressure relief button on the quick connect until the flow of water stops. WARNING FAILURE TO RELIEVE WATER PRESSURE, BEFORE DISCONNECTING THE QUICK-CONNECT FROM THE FAUCET, WILL RESULT IN BACK-PRESSURE OVER-SPRAY. THE TEMPERATURE OF INCOMINGWATER CAN BE VERY HOT, AND BACK-PRESSURE OVER-SPRAY COULD CAUSE SEVERE BURNS AND/OR SCALDING. DANGER DO NOT LET CHILDREN DISCONNECT THE DISHWASHER; CLOSE SUPERVISION OF CHILDREN IS ALWAYS IMPORTANT AROUND APPLIANCES. NOTE: Hard water conditions will adversely affect the washing performance of your dishwasher. Hard water conditions will also contribute to ‘lime’ (white film substance) deposits and/or ‘scaling’ on the stainless steel surface of the dishwasher tub and heater element, located in the sump underneath the removable filter screen. To assist in minimizing these conditions, it is recommended to periodically operate/rinse the inside of the dishwasher (empty) using 1 cup of white vinegar at least once a week. Disconnecting your Dishwasher • Shut off the hot water supply at the faucet. • Disconnect the power supply cord. • Remember to release the water pressure inside the inlet hose. Press and hold the red pressure relief button on the quick-connect until the flow of water stops. • Disconnect the quick-connect hose assembly by pulling down on the outer locking collar, (thus releasing the quick-connect from the faucet adapter). Before Using Your Dishwasher Remove the exterior and interior packing. * Check to be sure you have all of the following parts: * 1 Rack 1 Cutlery / Silverware Basket 1 Measuring Spoon 1 Measuring Cup 1 Instruction Manual Clean the interior surface with lukewarm water using a soft cloth. Operating Instructions To get the best performance from your dishwasher, read all operating instructions before using it for the first time. You can locate your model number on the tub wall just inside the door. Throughout this manual, features and appearance may vary from your model. Control Panel 1 Rinse-Aid Warning Indicator 4 Wash Program / Cycle Selector Knob 2 Start / Reset Light 5 ON / OFF Power Button 3 Start / Reset Button 6 Power Indicator Light Status Indicator Light – Description Light – OFF Dishwasher is in Stand-by mode. Light - ON Dishwasher is in PAUSE mode. Light – Flashing Dishwasher is in RUN mode. Operating Your Dishwasher a) Ensure that all Electrical, Water, and Drain connections have been installed correctly before proceeding. b) Load the dishwasher accordingly (See the “Loading the Dishwasher Rack” section on pages 15 – 16). c) Add the appropriate amount of dishwasher detergent to the dispenser (See the section “Proper Use of Detergent” on page 13). d) Close the door and ensure that the door latch has engaged. e) Turn the dishwasher ON by pressing the ON / OFF button. f) Select the appropriate wash cycle / program (See the Cycle Sequence / Program Description section on page 12). g) Make sure that the water supply is turned on to full pressure. h) Press the Start/Reset button, the dishwasher will begin to start. The START / RESET indicator light will begin to flash intermittently to indicate the dishwasher is in “RUN” mode. NOTE: When you press the Start/Reset button to pause during washing, the program light will stop blinking and the dishwasher will beep once every minute unless you press the Start/Reset button to start (See Pausing the Wash Program / Cycle). Pausing the Wash Cycle / Program: In order to make any changes to the selected wash program / cycle, load additional items, or remove previously loaded items the dishwasher must be put in...

Download now

Please, enter two numbers from picture: