Votes - 3, Average rating: 4.7 ( )

Manafacture: Moyer Diebel File size: 1.01 mb File name: Language of manual:

Remove all dishes from machine. 2. Remove any chemical pick-up tubes from their containers. 3. Place each tube in a container of fresh water and prime the chemical lines for several minutes to thoroughly flush chemical from the lines. Leave pick-up tubes out of their containers. 4. Drain the machine and refill with fresh water. 5. Spray interior walls with delimimg solution and let sit for 5 or 10 minutes depending on amount of build-up. Add deliming solution to wash tank. Do not let chemicals sit for longer than 15 minutes. 6. Close the doors to run an automatic cycle. 7. Repeat Steps 4-6 if necessary. 8. Lift the drain lever assembly and drain the machine. 9. Refill the machine and run a complete cycle two additional times. Drain and refill the machine after each cycle to thoroughly flush any deliming solution from the interior of the machine. 10. Flip the power switch to OFF. 11. Drain machine. 12. Deliming is complete. TROUBLESHOOTING TROUBLESHOOTING Perform the seven checks listed below in the event that your dishwasher does not operate as expected. 1. All switches are ON 2. Drain-overflow assemby is in place and seated 3. Wash and rinse nozzles are clean 4. Wash and rinse pipe assemblies are installed correctly 5. Scrap screens are properly positioned 6. Thermostat(s) are properly adjusted 7. Detergent and rinse additive dispensers are adequately filled If a problem still exists, use the following table for troubleshooting CONDITION CAUSE SOLUTION Machine will not start Doors not closed ................................... Door safety switch faulty ...................... Start switch faulty ................................. Main switch off ..................................... Overload protector tripped ................... Make sure doors are fully closed Contact your service agency Contact your service agency Check disconnect at main panel Reset overload in Control Box Machine washes Extended wash switch in....................... Push Extended wash switch constantly extended wash position down to the off position Low or no water Main water supply is turned off ............ Drain-overflow assembly is not ............ in place and seated Machine doors not fully closed ............. Faulty fill valve ..................................... Machine not filled initially ................... Clogged strainer in fill valve ................ Turn on house water supply Place and seat drain-overflow Close doors securely Contact your service agency Push Power switch UP to fill Clean or replace Continuous water filling Stuck or defective Fill Timer ................ Fill valve will not close ......................... Drain-overflow not in place .................. Contact your service agency Clean or replace Install drain-overflow assembly Wash motor not running Overload protector tripped .................... Defective motor .................................... Reset overload in Control Box Contact your service agency Wash tank water temperature is low when in use Incoming water temperature ................. at machine too low Defective thermometer Defective thermostat ............................. Defective heater element ...................... Defective solenoid valve ....................... Heater elements ..................................... Raise temperature to: 110-140°F/43-60°C for MH60 180°F/82°C for MH-6N 120°F/49°C-140°F/60°C for MH6L Check or replace Check for proper setting or replace Check or replace Check or replace Clean and delime have soil/lime buildup TROUBLESHOOTING TROUBLESHOOTING (Cont.) CONDITION CAUSE SOLUTION Insufficient pumped Clogged pump intake screen ................. Clean spray pressure Clogged spray pipe ............................... Clean Scrap screen full.................................... Must be kept clean and in place Low water level in tank ........................ Check drain-overflow assembly Pump motor rotation incorrect .............. Reverse connection between L1 and L2 in Control Cabinet Defective pump seal .............................. Contact Service Agent Insufficient final rinse Faulty pressure reducing valve ............. Clean or replace or no final rinse Improper setting on pressure ................. Set flow pressure at 20-22 PSI/ reducing valve 138-151.8 kPa Clogged rinse nozzle and/or ................. Clean pipe Improper water line size ....................... Have installer change to proper size Clogged strainer in fill valve ................ Clean or replace Low final rinse Low incoming water Check the booster (MH60, MH6N) temperature temperature ........................................... be sure the thermostat is set to maintain180°F/82°C temperature. MH6L check incoming water is set Min. 120°F/49°C-140°F/60°C. Check valve to be sure it is clean and operating Defective thermometer ......................... Check for proper setting or replace Poor washing results Detergent dispenser............................... Contact detergent supplier not operating pro...

Download now

Please, enter two numbers from picture: