Votes - 3, Average rating: 4
(
)
)
|
manual abstract
Top spray arm K. Washing filter G. Basket height adjuster L. Detergent and rinse aid dispenser H. Lower basket M. Turbo dry fan I. Bottom spray arm L The Controls . A. ON-OFF Button H. Half load indicator light R. Start / Reset button S. Low Salt indicator light This light informs you that the half With Start the wash cycle begins, This light warns you that it is time Press this button to switch the load is selected. whereas a;; the settings are to add more salt. appliance on. P. Cycle select button cleared with Reset. T. Low Rinse Aid indicator light B. ON-OFF Indicator light Each time this button is pressed, This light warns you that it is time This light informs you that the one of the cycle indicator lights to add more rinse aid. dishwasher is on. “E” will come on in sequence C. Door opening handle Use this handle to open the door. D. Delayed start select button This button delays the start of the wash cycle you selected by 12, 9, 6 or 3 hours. E. Cycle indicator light This light informs you which cycle you have selected or the one in progress. F. Half load selection button To allow you to wash a half load in the upper basket. G. Cycle phase and delayed start indicator lights Thes indicator lights inform you which cycle phase is underway (prewash,wash,rinses,drying). If you have set a delayed start, they also indicate the amount of time left until the wash cycle starts. J K H F E I M This dishwasher conforms to the 7HFKQLFDOFKDUDFWHULVWLF. following European Community Width cm. 60 Directives: Depth cm. 60 . 73/23/EEC of 19/02/73 (Low Voltage) and subsequent Height cm. 85 modifications; . 89/336/EEC of 03/05/89 Capacity 12 standard place settings (Electromagnetic Mains water pressure 4,3 psi -145 psi (30 KPa. 1MPa) (0,3 .10 bar) Compatibility) and subsequent modifications Power voltage See data plate . 97/17/CE (Labelling) Total absorber power See data plate Fuse See data plate D ISHWASHE. How to use your Dishwasher First of all. You've left out a dish? - Turn on the water supply Interrupt the wash cycle by press- tap completely. ing the On-Off button "A", then - Add the correct amount insert the dish you had forgotten. of detergent. When you shut the door, press the - Load the baskets On-Off button again. The cycle will correctly. start up from where you interrupted - Check that the spray it. arms rotate freely. - Close the door securely. Cycle end The end of the wash cycle is indicated by 2 short beeps and the -Press the ON-OFF button "A": flashing of the drying phase indicayou will hear a short beep and inditor light. cator light "B" comes on. Turn the appliance off by pressing Your appliance is now on and await-the On-Off button “A”, thus switching instructions. ing off the electricity supply. Turn off the water tap. Select the wash cycle. Wait a few minutes before unload- Select the wash cycle by pressing ing the dishes: they are very hot! If button "P". Each time this button is you wait a little while, they dry better pressed, a beep will sound and indidue to the steam. cator lights “E” will come on in Empty the lower basket first. sequence.Select the wash cycle most suitable for the type of dishes There's been a power to wash (see ‘Programme Chart’). failure or you opened the Close the door and press the Start dishwasher door button after a few seconds, you will The wash cycle stops and then hear a short beep and the wash cyrestarts when the electricity comes cle will started. back on or when you close the door. The dishwasher informs you. Your dishwasher has indicator lights "G" which light up to indicate the wash cycle phase that is underway. Modifying a wash cycle in progress. If you have chosen the wrong cycle - You can modify the wash cycle in progress, if it has only just started. Keep the Reset button "R" pressed in for approximately 5 seconds, a prolonged beep will sound, followed by three short beeps. Indicator light "G" will go out to show all the settings will have been cancelled. You are now free to reset the correct wash cycle. Delaying the start of a programme. When you have loaded the dishes, you can choose when to start your dishwasher before setting the wash cycle desired. Press button "D"to delay the start of the wash cycle by 12, 9, 6 or 3 hours. Each time you press it, you will hear a short beep and indicator light "G" corresponding to the selected delay will come on. Select the desired wash cycle. Press the Start button, you hear the beep, the countdown to the delayed start will begin. If, for example, you have set a 12 hour delay, once you have selected a wash cycle the 12 hour indicator light will flash... followed by the others in sequence until the set time delay is up. The indicator lights will keep you informed of the countdown progress at all times. Once this time is up, indicator light "G"will stop flashing and the wash cycle will begin. If you change your mind and you wish to set a different delay, just open the door, press button"D", you need not reset the wash cycle...
Other models in this manual:Dishwashers - FDW65 (811.67 kb)