Login:
Votes - 2, Average rating: 5 ( )

User manual Hotpoint, model BFI68

Manafacture: Hotpoint
File size: 1002.69 kb
File name: a7faaab9-e366-477a-8f1e-665cd14561a1.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


D ISHWASHE. Installation Choose where you want to install your dishwasher, you can place it so that its sides or back panel are side by side with furniture or up against the wall. The dishwasher is provided with water supply and drain hoses, which can be directed towards the left or right to facilitate appropriate installation. Levelling. Once the appliance is positioned, adjust the feet by screwing them in or out depending on how high you want it and to level it so that it is horizontal. Make sure that it is not inclined more than 2 degrees. If the appliance is level, it will help ensure its correct operation. Height Adjustment Insert the appliance into the cutout and then adjust the height using the screws located on the front bottom part of the machine. Use a screwdriver to turn the screws in the clockwise or anti-clockwise direction to increase or decrease the height respectively. Cold water connection. Connect the cold water supply hose, inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place (see figure 2). If the water hoses are new or have been out of use for an extended period of time, let the water run to make sure it is clear and free of impurities before making the connection. If this precaution is not taken, the water inlet could get blocked, causing damage to your dishwasher. A Fig.2 Anti-flooding protection Your dishwasher has a special system which stops the water supply in the event of leaks inside the appliance. It is equipped with a water inlet that has a clear outer hose and an inner high pressure hose which turns bright red if it breaks. Leaks are prevented as the clear outer hose now contains the water. It is vital that you check it on a regular basis, if you see it has turned bright red, you know you need to replace it as soon as possible. Call for an authorised technical engineer to come and replace it. Drain hose connection. WARNING: Connect your dishwasher drain hose to pipes which connect to the foul drain system and not to surface water drains. IMPORTANT: For the correct operation of your dishwasher, it is essential to comply with the following information: Standpipe: Ensure that the hose is not pushed too far down the standpipe. If the end of your drain hose is fitted with ‘retaining flaps’, ensure they are inserted fully into the standpipe. This will prevent the pipe from jumping out during installation and use. DO NOT position the standpipe near an electrical outlet. ENSURE that the drain hose is not kinked and it is routed as shown in the diagram. The standpipe should have a bore of at least 38mm (11/2”). It should be installed as shown, have a trap fitted and must discharge into the same drain system as your household sink. It MUST NOT be connected to a surface water drain. Ensure the drain hose is securely attached, to prevent it coming away while the machine is in use and causing a flood. Sink Waste System: For under sink drainage: Before connecting the drain hose, remove any internal restrictions This will prevent a build up of debris which could cause a blockage. Remove any restrictions from the waste spigot and ensure that the sealing bung is removed. The hose should be routed, such that it is raised to a minimum height of 800mm (31/2”). NOTE: Ensure the sink outlet pipe has a minimum diamtere of 32mm. 1. Untie the end of the GREY drainage hose from the rear of the appliance. 2. Reposition the ‘Hooked End Support’ as required along the GREY drainage hose. 3. If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug. 4. Attach the GREY drainage hose to the under sink waste disposal unit securely, using the clip and rubber tube supplied. D ISHWASHE. Getting to know your Dishwasher E. Upper basket I. Bottom spray arm F. Top spray arm J. Salt container cap G. Basket height adjuster K. Washing filter H. Lower basket L. Detergent and rinse aid dispenser M. ‘Turbo Dry’ fan E G F H I K L J M The Controls A. ON-OFF Button Press this button to switch the appliance on. B. ON-OFF Indicator light This light informs you that the dishwasher is on. C. Delayed start select button This button delays the start of the wash cycle you selected by 2, 4 or 6 hours. D. Delayed start Indicator light This indicates that the delayed start has been set. E. Extra drying button Press this button for greater drying. Q. Basket selection button Press this to choose whether you want dishes on the lower or upper basket to be washed. R. Basket indicator light This light shows the basket selected. M S. Low Salt indicator light This light warns you that it is time to add more salt. T. Low Rinse Aid indicator light This light warns you that it is time to add more rinse aid. ST Q P. Wash Programme Selector Each time this button is pressed, one of the cycle indicator lights “M” will come on in sequence. M. Cycle indicator light This light shows you which cycle you have selected or the one in progress. C BA 1 2 DRP E Technical C...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category