Manafacture: Hotpoint
File size: 584.64 kb
File name: 32b1fd3d-3486-48d0-9a50-8cb7c9d8500e.pdf
|
manual abstract
Use a screwdriver to turn the screws in the clockwise or anti-clockwise direction to increase or decrease the height respectively. Adjusting the back Feet Insert the appliance into the cutout and then adjust the height using the screws located on the front bottom part of the machine. Use a screwdriver to turn the screws in the clockwise or anti-clockwise direction to increase or decrease the height respectively. Condensation-proof tape. On some models, a transparent condensation-proof adhesive tape has been provided. It should be stuck onto the lower side of your wooden worktop to protect it from the formation of condensation. When not provided, this tape can be requested as a spare part from authorised retailers. Cold water connection. Connect the cold water supply hose to a 3/4 gas threaded connection, taking care to screw it tightly onto the tap. If the water hoses are new or have been out of use for an extended period of time, let the water run to make sure it is clear and free of impurities before making the connection. If this precaution is not taken, the water inlet could get blocked, causing damage to your dishwasher. Anti-flooding protection Your dishwasher has a special system which stops the water supply in the event of leaks inside the appliance. It is equipped with a water inlet that has a clear outer hose and an inner high pressure hose which turns bright red if it breaks. Leaks are prevented as the clear outer hose now contains the water. It is vital that you check it on a regular basis, if you see it has turned bright red, you know you need to replace it as soon as possible. Call for an authorised technical engineer to come and replace it. Drain hose connection. WARNING: Connect your dishwasher drain hose to pipes which connect to the foul drain system and not to surface water drains. IMPORTANT: For the correct operation of your dishwasher, it is essential to comply with the following information: Standpipe: Ensure that the hose is not pushed too far down the standpipe. If the end of your drain hose is fitted with ‘retaining flaps’, ensure they are inserted fully into the standpipe. This will prevent the pipe from jumping out during installation and use. DO NOT position the standpipe near an electrical outlet. ENSURE that the drain hose is not kinked and it is routed as shown in the diagram. The standpipe should have a bore of at least 38mm (11/2”). It should be installed as shown, have a trap fitted and must discharge into the same drain system as your household sink. It MUST NOT be connected to a surface water drain. D ISHWASHE. Sink Waste System: For under sink drainage: Before connecting the drain hose, remove any internal restrictions This will prevent a build up of debris which could cause a blockage. Remove any restrictions from the waste spigot and ensure that the sealing bung is removed. The hose should be routed, such that it is raised to a minimum height of 800mm (31/2”). NOTE: Ensure the sink outlet pipe has a minimum diamtere of 32mm. 1. Untie the end of the GREY drainage hose from the rear of the appliance. 2. Reposition the ‘Hooked End Support’ as required along the GREY drainage hose. 3. If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug. Ensure the drain hose is securely attached, to prevent it coming away while the machine is in use and causing a flood. D ISHWASHE. Getting to know your Dishwasher E. Upper basket F. Top spray arm G. Basket height adjuster H. Lower basket The Controls A. ON-OFF Button Press this button to switch the appliance on. B. ON-OFF Indicator light This light informs you that the dishwasher is on. C. Delayed start select button This button delays the start of the wash cycle you selected by 2, 4 or 6 hours. D. Delayed start Indicator light This indicates that the delayed start has been set. E. Extra drying button Press this button for greater drying. M. Cycle indicator light This light shows you which cycle you have selected or the one in progress. P. Wash Programme Selector Each time this button is pressed, one of the cycle indicator lights “M” will come on in sequence. Q. Basket selection button Press this to choose whether you want dishes on the lower or upper basket to be washed. I. Bottom spray arm J. Salt container cap K. Washing filter L. Detergent and rinse aid dispenser R. Basket indicator light This light shows the basket selected. S. Low Salt indicator light This light warns you that it is time to add more salt. T. Low Rinse Aid indicator light This light warns you that it is time to add more rinse aid. Q M ST CBA E G J I L K H F E 1 2 DRP Technical Characteristics Technical characteristics Width Depth cm. 59,5 cm. 57 This dishwasher conforms to the following European Community Directives: Height cm. 82 . 73/23/EEC of 19/02/73 (Low Voltage) and subsequent Capacity 12 standard place settings modifications; . 89/336/EEC of 03/05/89 Mains water pressure 4,3 psi - 145 psi (30 KPa. 1MPa) (0,3 .10 bar) (Electr...